RE34BAF3 Frigidaire Range - Instructions

Pulled out the old drip bowls and replaced with the new. A simple snap!

Pretty easy installation; you lift the top plate up and snip the wires maybe four inches away from the burner. Leave more wire than you think you need; once you get into it you'll realize you need more wire length than you think.

Then strip the remaining ends, twist them together with the provided caps, and use the heat shrink to hold it together. Remove the old terminal, replace it with the new ones, and you're good to go!

Remember to check that the wires are tight in the cap before heat shrinking, though. I had to get more shrink wrap in order to finish.

Just followed the instructions

Took out bottom drawer and unplugged power cord, slid unit out to reach back panel,removed front door( 2 Phillips screws) making it easier to reach back of oven, removed screws inside of oven holding element in place, took plate off rear and removed the spade connectors with needle nose pliers. Slid new element into oven and replaced screws inside of oven. Connected the two spade wires on the back and replaced rear panel. Slid unit back in place and plugged the 220v power cord back in. Straightforward and very simple! It took 3 times longer to clean the oven while it was disconnected than it did to replace the element.!

The repair was very simple and easy. All I hqad to do was remove the old knobs and attach the new ones. No tool was required.

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Your website is great...easy and it literally took me no mote than 5 minutes to find what I needed and order...and received it VERY quickly. Must say I was dreading going to some parts house that we have in our town in bad area, and searching on dusty shelves for what I needed...am so glad I found you!!

I pulled out the stove from the wall and unplugged it. I then used a socket set with a long extension which made it easier to reach the rear wall of the stove. After removing the screws i gentle pulled the element forward and exposed the clips and wires. I removed the clips. The wires seemed to want to slip back into the hole so I used clothes pins to hold them in place. After I received the new element (Two Days) I reversed the process. Using a socket set it is very easy to tighten the screws to much. Be careful to just snug the screws. I plugged the unit back in and slid it back in place and turned it on.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element

Removed back cover, unhooked wires, unscrewed and removed bad baking element. Reverse order to install. Less than 15 min. repair job.

First unplugged the stove, then removed the screws holding the element in place. Next I pulled the element out until the wires were visible and unplugged them. After removing the old element, I plugged the new one in and positioned it with the screws. Plug the stove back in and done.

I just removed two screws. Pulled the element out, unhooked the wires. plugged the wires into the new element screwed it in and was done

Unscrew the old one and unplug the wire leads. Then plug in the new one and bolt back up.

Pulled stove out, removed screws that hold the element in place. Then pulled element out a few inches, diconnected the two wires. I connected the wires to the new element and put everything back to right. It was quick and easy.

Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!