Enter the code DIYDAD10 at checkout to apply your discount. Discount will be applied at checkout when the code is entered & applies to all parts. Cannot be combined with any other coupon or special offer & cannot be applied to a previously placed order. Not valid toward tax or shipping & handling. Discount has no cash value. Discount expires on June 17 at 11:59pm EST.
You've Got 10% Off Your First Order!Save 10% with code at checkout *click to copy coupon code
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
It was a rather simple fix--just replacing burner pans
Problem I had was finding the right ones to fit the stove top. Burner pans that tell you will fit most stoves, do not. After I had paid over $20.00 for some that did not fit, I got on the internet, found you, ordered the replacement parts and had them within a few days. Put them in and there you go. A perfectly happy me and a nice looking stove again.
removed the plug that had burned up on one of the top burners, replaced it with a new plug purchased from parts select., it was quite easy ,I unpluged stove and raise the top exposing wiring for the burners cut the old plug wiring and connected the wires for the new plug with connectors and shrink tubing supplied in the repair kit easy and quick repair
Of course, power off first, then I removed the old one and inserted the new one, make sure everything in right place, then turn on power, simple as 1-2-3.
The larger burners would stop working while in use.
The removal of the old burner and installation of the new burners was easy. Just lift the opposite side that rests on the rim and pull burner out. New burner then gets inserted and the opposite side goes right into rim. It took all of 30 seconds to replace both burners. I wish I had replaced these when they first started to go!!
Removed all surface burners from range, removed range top screws, and suspended range top. Removed plug-in block mounting screw. Cut wires for plug-in block close to original wire-nut junction. Inserted contacts & wires from kit into plug-in block. Slid a provided shrink sleeve onto each wire. Stripped wires on range wires and then connected them to the plug-in block wires with the provided high-heat wire nuts. Selected one of the two provided plug-in block brackets that matched the original bracket on the range. Used a butane lighter to shrink the shrink sleeves over the wire nut connections. Snapped the appropriate bracket onto the plug-in block. Reassembled everything in reverse order and plugged in new element. Note: my only two issues are that the two high-heat wire nuts provided in the kit were a bit too small for the wire gauge in my Whirlpool range. It took some fiddling on my part by carefully re-stripping the range wires to get the wire nuts twisted on securely. Two more wire nuts of the next size up would have been appreciated. Also, I found that the provided plug-in block mounting screw did not find fit my range. No problem; I simply re-used the original screw. All in all, an easy repair and the element works perfectly.
Surface Element switch faulty with no control on heat
Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element making sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.
I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.
The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.
I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.