RBS275PDB13 Whirlpool Wall Oven - Instructions

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

I found several posts about Whirlpool/KitchenAid ovens having this problem and most of the time this required a replacement of the thermal fuse. Other than the large number of screws to remove the oven and the sheet metal coverings, replacing the fuse was mostly about waiting to get the part. If I had a local dealer with the fuse, I probably could have been baking Deep Dark Chocolate Cheesecake that same evening. Even so, this particular repair should be left to those familiar with doing moderate-level handyman type repairs. You have to make sure the breaker is off and beware of the sharp edges on sheet metal. Fortunately, the fuse was easy to find using online documentation for my model. Part Select was very helpful when my original order did not arrive. Their customer service was great!

The repair went well & the part came in on time for thanksgiving thank you

Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.

With some help from my wife.

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

I followed these instructions put in by a fellow customer. These were very helpful. Just make sure the glass is finger print free before you put it all back together. My time was 30 minutes end to end. =========================== The first thing I did was to remove the oven door by releasing the two latches on the hinges (by hand). I then raised the door toward the vertical position and lifted up. The hinges slide out of the oven housing. I laid the door, inside face up on my island counter top. This ensures that none of the parts will fall when disassembling the door. Next I unscrewed the screws 4 top and bottom and four on the inside face. This releases the frame from the front housing. Lift the frame off the door, exposing the glass pieces. Lift off the broken inside glass and place the new piece in the glass retaining housing. Replace the outside frame and replace all screws. Take door back over to oven and slide hinge bottoms back into slots on oven. Rotate to horizontal position and flip latches back to locked position. Total time was about 10 minutes mainly because I was curious how the door was constructed and I poked around while it was disassembled

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

Like others said, the trick was getting the oven door off. If you don't have the instructions, here's how: Open the door all the way. Shine a flashlight on the hinge, and you will see an open hole about 3/16" diameter below the hingepin and toward the oven. With the door open, put a 5/32" allen wrench or any other comparably-sized metal pin into the hole in each hinge. With the pins in place, close the door as far as it will go, which is almost but not quite fully closed. Put one hand under the door handle, the other hand under the bottom of the door, and pull the bottom of the door down and out. With maybe a little wiggling, it will come right out. That's really all there is to it! Taking out all the glass layers is straightforward; you don't need any instructions to see how to do it.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Unscrewed the old thermostat took off the conectors then replaced with new one, and screwed it back on.