RBS245PRB05 Whirlpool Wall Oven - Instructions

Removed and replaced boiler element

Remove rear panel - remove sensor from inside - unplug from rear - reverse to install - did not fix problem

GENERAL APPROACH:
1) Checked YouTube for some general guidance: VERY helpful things there for this! PartSelect's install info. was helpful as well- Thank you for this!
2) had table set up in order to disassemble the door once it was removed
3) There are 4 separate glass panes in there- they all need to be cleaned
4) TOOK PICTURES AND MADE CAREFUL NOTES AS (12 or 15?) SCREWS ARE TINY & THERE ARE DIFFERENT TYPES. TAPED THEM NEAR WHERE I REMOVED THEM SO AS TO KEEP THINGS STRAIGHT
5) Like any project little or big, just take your time & it actually works out well
6) take advantage of this downtime to clean the oven good, as well as the door & panes of glass. Cleaning was 75% of this project.
7) EXTRA: If you're so inclined, turn the breaker off for the Oven & carefully remove the lower heating element to enable easier & more thorough cleaning of your oven. You'll be glad you did this- and so will your cook!

I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.

All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.

Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.

I bought an old house where this Double Wall oven was not working. I looked at the suppressor and one of the Red diodes was burnt. So, I removed it, took a picture of it and send it to the sales rep. She located the part exact part and sent it within 3 days. Then I installed it and the oven worked beautifully. My Appliance repair man gave me an estimate of $760.00 and I was able to repair within 30 minutes and $60.00 part. Really happy, Thank you .

Cut the power. Undid the screws to the element. Popped off the old element replaced with new,put screws back in turned power back on and Shazam it was up and going

Sorry but that would take too long to give all instructions, but I will mention that there were four glass plates if you count the cover of the door which is a large glass piece. All glass plates had to be taken out or off including the holder hardware in order to get to the inner glass (about 15 screws in all). No you-tube videos seemed to apply directly for this door. Taking some pics and using a card to hold screws in the pattern they were taken out helped keep the in order to be replaced (I screwed the screws into a paper sheet to keep the pattern with some labeling like top, bottom, etc). Lower glass door appears to only have two glass plates (didn't take it apart, but inner glass holders were not seen when peering in through the inner glass as they are in the upper door). If the inner glass plate on this door gets broken it should be easier. The glass was broken for some time before this repair so there was a lot of cleaning required inside the door. Oh, by the way, when taking out the door off pull out (not up) after locks are released and when the door is mostly closed. Push back in and open door down a bit to lock back in place. This is far from complete but I hope it helps some.

1. Disconnect AC power 2. Remove back with several sheet metal screws. 3. Remove wires from Limit Thermostat. 4. Check Limit Thermostat continuity -- if open then Limit Thermostat is faulty. 5. Remove Limit Thermostat with two screws. 6. Install new thermostat

Verify power is off to the oven, turned main power supply off for the oven at the breaker panel, located the securing screws for the defective element, used a Phillips screw driver to remove the screws, pulled the element slightly out unit wires are exposed, verify 0 volts at the element wiring terminals, used pliers to remove the wires to complete the uninstalling process, reinstall the element in the reverse order, restored power at the breaker panel

I was able to remove the old element and planned it with what little time off that I could. This would have been maybe 20-30 minute repair at the most. HOWEVER! I was extremely irritated screws were not included? When I called to ask if they were missing they said they didn’t come with the element. Cost me a very annoying trip to the hardware store. Not sure if I missed it on the site that they don’t provide screws - would have been nice to know that before I started. Still scratching my head as to why screws wouldn’t be included? My old ones were as beat up as the element I replaced. I was so irritated I was looking for a spot to leave feedback. Product is fine. Shipping was fine. Sending these products out as they do? Zero stars on that.

Well, the instructions on the computer site were very easy to understand, however, the difficulty lay in the fact that we were 2 78 yr old people and getting to the inside the oven, lifting up the element so that we could see where it should be connected and get it connected was a task. We had to get down on our knees and then get back up. That was a chore within itself. But, the instructions were easy and clear.
Bottom line if us old people can do it, anyone can.

The tech said he used No 2 Phillip's. Once I took the door off and removed the racks I quickly learned a Phillips was not going to work. I am now the proud owner of a Kobslt star and square ratchet screwdriver.

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

Only problem. stripped screw. Replaced at local hardware store. Directions were simple and easy.

Unplugged old element unit and plugged in new element. Took two needle nose pliers and a flexible body. Took about 5 minutes. Works fine. Anybody can do it. Make sure power is off at the box.