RB942G201 Hotpoint Range - Instructions

Partselect had the right part, clearly indicated in the diagrams and menus. Shipped quickly. Easy to use web site.

Replacement element also failed to heat.

Possible that the problem is with the stove itself, not with the surface element.

Pulled out the old burner that was held in by a metal spring clamp. Pushed the new one in.

Good as new.

We just remove the old surface unit and insert the new one by hand. Thanks to PartSelect, we were able to buy really good quality part that works right away! It was a 26-year-OLD GE Stove/Microwave space maker, the parts were hard to find in stores. Thank you for selling this! All the best for your business!

Replaced old drip bowls with the new ones. Very simple, no tools required.

1. Went on line to your website.
2. Ordered the parts
3. Rec'd your package.
4. Installed ("plugged in") the new parts.
5. Voila !

it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank

I have had to replace this unit once before. It was very obvious which terminal had burned off. Removed the total front panel. Removed the timer and replaced wires from one unit to the other. Also had to strip off one wire connection and replaced it .

Took oven door apart to get to gasket. . . Took about an hour or less. Then I basically cleaned the entire over door while I waited for the part to come. When the new gasket came I started to put it back on. I used springed type clothes pins to hold the gasket in place on the middle part of the door which hold the glass. As I put on the out part of the oven door over the middle part of the oven door, I carefully took the pins off as I gradually slipped the 2 parts of oven door back together. After the gaskets were carefully adjusted to it's proper position, then I put the nut screw back in through the gasket holes to hold the 2 oven door parts back together. Then, I finally put the rest of the door back together. This took about an hour also. Not to bad when you have to do this by your selves. This is the second time I've put in a new oven gasket. The oven is 28 years old, so the gaskets last me about 14 years each time. We hope to keep the oven a few more year before we buy a new glass top style stove. Hope this was helpfull to all you diy's !!! Don

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

1) Took photo of original wiring behind original clock. 2) Marked up wiring instructions for new clock with wire colors. 3) Marked wire colors next to posts on new clock. 4) Removed old clock and its metal mounting bracket. 5) Installed new clock onto old mounting bracket.PROBLEM: The holes in the glass facade of oven are shifted about 1/4" off from the pushbuttons on the new clock. 6) Remove bracket and enlarged holes by 1/4" sideways. This includes shifting the holes for the oven light pushbutton switches, and the four "racetrack" holes where the bracket attaches to the oven. Plug wires into new clock, using extender wires provided as needed. Labelled extender wires with their "colors". POWER UP. The clock works, and the "Timed Bake" works. However, the Self-Cleaning of the oven cannot be started, because the latch level cannot be moved to the right (locked ) position. This leaves us unsatisfied, as restoration of Self-Cleaning was the reason we decided to replace the oven clock.

The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.

Good directions

The original controls were different for the small burners and the large burners. The replacement part fits all. Before removing wires, pay attention to writing on new and old control and replace 1 at a time. The hardest part was being sure to cut the knob stem to the correct length. Control works well.

Remove oven door, removed Phillips head screws on perimeter of oven chamber, loosened four or five square head screws to facilitate the removal of the old gasket, (this gave enough room/play to pry the oven chamber slightly) then removed the old gasket, and re-assembled the oven, and replaced the door.