RB757BB1 Hotpoint Range - Instructions

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enough slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

First, we ordered the part on Sunday afternoon online. It was here by Tuesday morning. We unplugged the oven and removed the screws holding the element in place and the electrical contacts. That was the toughest part because it's hard to get in the oven and they were baked on pretty well. We had to drill holes in the bake element. Be careful not to drill them too big, so the screw will fit snug and make contact. We screwed the bake element to the contacts, then back to the over, plugged it in and turned it on. The temperature is more constant and steady than ever, and the oven heats much faster. We were impressed and happy to avoid replacing the whole stove.

I removed the two screws that hold the element in place. I pulled the element out about three inches and
disconnected the two wires. The screw holes in the new element would not accommodate the old screw size so I enlarged the holes to fit. Connected two wires and replaced two screws that hold element in place. End of story.

First I unpluged the appliance. Then I removed the cover from the back of the range. I then disconnected the two wires from the element. I then removed the two screws that hold the element in place. I then removed the old element and reversed the process to install the new one.

Unplugged oven. Pulled out from wall and removed backside access panel. Unplugged 2 stake-on connectors connected to element. From front side of oven, removed fan guard using 1/4 inch nutdriver. Gained access to and removed two screws holding in element. Pulled element out. For installation, reverse process.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Plugged in new burner.

I unpluged stove then opened slightly oven door and lifted it off to get closer. Then with a light to help I took out two screws and pulled the element out. I didn't need pliers to get the wires that are put on with slide on clips. you may need a pair. put wires on slide in place put screws back ,replace door, plug it in and test. Very easy.

Took out the old & put in the new one-Done!

unpluged unit then removed back panel unpluged element then took the two screws out took old element out replaced with new one put screws back plug element back in put back panel on pluged it in and started baking home made chocolate chip cookies

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

This was extremely easy! I unscrewed two screws, pulled out the old element, inserted the new element and screwed the screws back in. Also, this part came very quickly through the mail. If needed, I will definitely use this site for repairs again.

Flipped off the breaker for the stove. There were two screws holding the old element in place. Removed those, pulled the element out a little to expose two wires, disconnected those, swapped in the new element, reconnected the wires, and screwed it back into place. Flipped the breaker back on and voila! Barely more difficult than changing a lightbulb.

I simply pulled the old ones out and replaced them with the new ones. It looks so much better and cleanes up well.