RB753BC3CT Hotpoint Range - Instructions

Was a piece of cake removed 2 screws, pulled element out. Pulled the wires ooff the old unit and put them on new unit and screwed it back in.

removed element found a crack and replaced with new one I got from PartSelect.com. with fast fast shipping,thanks you saved me for spendin more money on a new one. it happened on christmas day of course......

turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next ....awesome

Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.

First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.

I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed the 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy

Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting to work on it.

Removed old socket, I had replaced with a aftermarket that really did not work well. When I recieved the terminal block kit from your company it was the proper kit. Service was better than expected, part and price was great and it took very little time ti install. Thank you.

I ordered the oven rack on a Tuesday and received it the very next day - was wowed at the service.

Easily glide in.

The person I spoke to knew exactly what I was trying to describe. The part arrived in 2 days. 5 minutes later the drawer was back in place. I was glad I save the screw as the part did not come with one.

The repair was very easy. It did require a very small torx driver (I can't remember the size off hand.) and a 1/4" nut driver.

attached the element,pushed it back in the pocket,put the plate back on, screwed the nut and bolt back on and was done in less than 4 minutes!!