PVTEST1Q Maytag Washer - Instructions

Bought the parts and just inserted them.

Wow! Thanks to the customer info/hints already posted the repair went super smooth and was relatively easy to accomplish. $70.00 for an easily replaced part sure beats $1,000+ for a new washer. Super fast shipping reduced down-time significantly!!! From start to finish the job took less than 30 minutes. Thank you so much.

Download machine service manual from internet. This makes dismantling easy and prevents damage to component parts.

Dismantle as per manual and remove old bellow - easy.

Re-install new bellow on tub rim - EXTREMELY difficult. The spring that tensions the wire that holds the bellow in place is extremely powerful and in attempting to stretch it it often slips off the tub rim taking the bellow with it so you have to start all over again. It took me 2 hours to realise I would never be able to do this alone. With the help of a second pair of hands this was accomplished in 20 mins with some difficulty.
The rest of the installation and re-assembly was done without difficulty.

Despite the reviews by people who installed this part themselves, I knew that any type of repair was beyond my ability. I enlisted the assistance of a cousin who is a trained, professional appliance repairman. Despite not having instructions, with his experience things went well until he found he did not have the unique wrench that would have made life easier, but he was able to adapt and use the tools he had at hand. Unfortunatley, after more than twos hours attempting to install the wire around the boot, he realized that he could not do it alone, I had to help him and together, we were able to install the wire. It would have been helpful to have step by step instructions and a list of necessary (or at least useful) tools.

Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.

Basic disassembly as described earlier.Some tips I found helpfull. Use vice grip pliers on spring.it will keep a grip on the spring hook and you can exert more force to pull the spring.Th bellows was very sticky and hard to slip into place. I put a litle silicone lube ( stuff you use for pool pump gaskets )on the bellows. It made it slip into place easly.

Removed the door and front panel with ease. Then came the spring and cable. People who say it was easy are not telling the whole story. Removing the spring was okay except for it flew across the room. Putting the new cable on with a pair of needlenose pliers did not work for me. I had to get a spring tool like you use on brakes on a car. Once I had the tool and secured the cable in place with a piece of wire I got the spring on. Everything except the spring took about 15 minutes.

Disassembled washer as per directions with seal kit. Removed inner tub. Cut both tub shaft bearing in half; punched out from outter tub. Installed new bearings using .5 inch threaded rod, washer and bolts. Installed new seal on inner tub shaft. Installed inner tube. Re-assembled washer.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

Followed instructions that came with replacement part, good as new!

I removed the rear access panel, used a nut driver and pliers to remove the old hose. I tried to connect the new hose with the spring clamp on the pump end of the hose. I gave up on that after a few attepmts because the clamp was very hard to manipulate with standard pliers. I used a standard screw type hose clamp (2") that I had instead. The tub end was easier because a standard hose clamp was used there already. The washer no longer leaks, and I saved a lot of money by doing the job myself!

Found the part on parts select, which also had a very helpful DIY repair video to replace the part. I followed the video step by step to fix the tub cover, and the washer is back to full working condition!!! I could not be happier with Partselect.com. Their easy appliance break down to find the exact part that is broken; but to also include a instructional video for that part was amazing.

On-line instructions were found easily enough. And followed easily. Hard part was placing the cable and spring which secures bellow on drum. One instruction said "you cannot do this by yourself" (I couldn't see how help would have "helped") the other said "this was the hard part" of repair. I weight 115 lbs and it took me 1/2 hour to finally get the spring hooked through cable end it's a very STIFF spring! I only had a short pair of needle nose pliers - an 8-inch pair would have given me more leverage and shorten "hook-up" time.

Followed the video, besides the spring, everything was easy.

I just followed what others have already noted. The only challenge was the spring as others have already stated many times. You will need help but be patient and you'll make it work.