PSCF3VGXAFWW General Electric Refrigerator - Instructions

The trouble shooting information on the web site indicated that the damper door within the climate control unit may be broken. This was easily confirmed and the replacement of the climate control unit immediately returned the food locker temperatures to the digital electronic thermostat settings. The part has an improved ventilation gasket interface between the food locker and freezer. The unit works perfectly again, and the food locker temperature is exactly what the thermostat setting is.

There is no access to the inside of the door to replace the water line. I was able to insert a 1/4" drip line barbed connector into the old line at the base of the door and then connect that to a piece of the plastic tubing which I then connected back to the original water supply tubing with the 5/16" union. It took three attempts to get the tubing through the bottom hinge without a crimp in it. It's best to have a second person to hold the door while you "fish" the tubing through the hinge.

This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!

This is the second or third time this cup has broken. Maybe we use more crushed ice than the average family, but you would think this part could be more durable. Anyway, I digress. This is about the repair. Four screws removed around bottom of tray, one screw removed for some bar that mechanically opens a door to allow ice to fall out of the tray, and two butter knives used to release tabs around the screw components... and we were done.

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Removed the ice maker from the freezer. Unscrewed the outer cover/base of the ice maker. Unscrewed the long lever that opens the ice chute. This freed up the feeder coil enough to pull it out enough to replace the cup drive. Once I replaced the cup drive, I laid it back down into the ice maker bin, reattached all the screws and it worked! The old cup drive had a tine broken off which would not allow the feeder coil to turn. It seems like a weak part and I anticipate I may have to replace it again in a few years.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

I searched YouTube for the problem and was quickly taken to several videos that detailed to required actions. This encouraged me to proceed, so I took the back cover off and found the water valve leaking. I then googled the make and model of the frig and found the part. The YouTube videos provided all of the details needed to determine the problem and replace the faulty part. Once the part arrived, I was able to install the new one in a few minutes. Operation returned to the water dispenser and the leak was gone. Total cost of the repair was $56 and took about 1.5 hours to remove the original part, order the replacement and install it when it came. Perfect!

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

I removed the ice from the tray, took out the four screws from the tray, pulled up the metal spiral took out the old drive cup, replaced with the new one, replaced the screws and put the tray back in the freezer. A piece of cake. Thanks for your prompt service and the reviews on how to replace.

Removed ice bucket and observed the plastic drive bushing for the auger had the drive dog broken off. I removed the four screws on outer shell for the ice bucket, removed it and found the auger had key stoned a hole in the ice tray housing. At that point I decided to replace the ice bucket and auger assy. The new one works fine.

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

Took out ice tray and then slid motor out of right side bracket and sat on shelf. Removed the 3 screws holding up left side bucket glide first. Make sure you have correct size socket for the 3 screws on bucket glide. Works best with a screwdriver type socket tool. I then removed broken plastic piece from motor (screw in motor is different size than the ones for left side bucket glide). I put in new left side bucket glide (rear back screw a little bit of a challenge but it can be done) and then slid motor back into right side bracket and fastened motor to new plastic piece that sticks out from left side bucket glide. Put back in ice tray and good to go!

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.