PIE23NGTJFKB General Electric Refrigerator - Instructions

The trouble shooting information on the web site indicated that the damper door within the climate control unit may be broken. This was easily confirmed and the replacement of the climate control unit immediately returned the food locker temperatures to the digital electronic thermostat settings. The part has an improved ventilation gasket interface between the food locker and freezer. The unit works perfectly again, and the food locker temperature is exactly what the thermostat setting is.

I removed the screws out of the hinge while my wife put pressure on the door to hold it in place. I removed the hinge, replaced it with a new one, and screwed it back in place. Took just a couple of minutes. Easy and fast. The refrigerator was not leveled properly and that was why the door had swung back so fast, with enough force to eventually bend the hinge. I contacted geappliances.custhelp.com and used the chat option to speak to someone about how to lower the back wheels. They were extremely helpful in walking me through it. Now the refrigerator is leveled, and the door, when opened, will not swing back and contact the hinge. My overall experience in fixing this problem, from locating and ordering the correct part, to installing it, and then fixing the problem that led to the hinge being damaged in the first place, was outstanding.

This part (plastic tubing) does not show up under my model of refrig...so I had to look thru the various water lines and pick the one that "looked" right. Luckily, this is the exact replacement part and works perfectly. I removed the lower back panel from the fridge, removed the bracket holding the water line connectors and pressed the outer ring of the coupler up until it released the old water line. I pushed in the new line, made sure it was snug with a gentle pull and ran the line under the fridge up to the existing coupler. I removed the old line from the existing coupler under the front left of the freezer door, and pushed in the new line. I did not need to use the new coupler. If my old line would not have been so brittle and cracked in several places, I could have just cut out the leaking portion and popped the new couple in to mend the line back together. Easy job and we can stop buying bottled water at the store now!

Raised side of fridge enough to get 1/4" ratchet with 1/4" socket under roller wheel assy. Removed three hex-head screws to separate damaged wheel assy from fridge frame. From panel below fridge compartment, backed-out stripped leveling screw. Mounted new roller assy and then threaded in new leveling screw from front. Lowered fridge and adjusted leveling screw for proper height. Suggest putting a 2x4 under fridge for safety when hands are under unit.

Before replacing the top filter housing, ensure the inlet water valve is operational. Replacing is a straight forward process. Unhook the houses from the inlet water valve in the back of the refrigerator. Remove and replace the top filter housing and ensure you replace the sealant using plumbers putty or sealant dicor butyl putty.

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

look at how the unit was put together and disassemled it pice by piece and labeled parts as i took them of in order then reversed when i reassembled

Removed tray, threw out ice , removed 3 screws used 2 screw drivers to seperate part & re installed

Tube was too short so I used the union to attach additional tubing to reach the valve at the lower rear of refrigerator

It was a simple remove and replace. The new part fits directly in place of the old part. Its a pain to remove the light but once you get the light out the job is simple. The light must be pried out gently. It is snapped in place toward the air inlet cover and needs to be pried loose. Once the light is out there are 4 screws holding the air inlet cover in place. Remove the 4 screws and unfasten the wiring harness. Once the screws and wiring harness are disconnected remove the old part. Reinstall the new part in reverse order.

Replacing the water filter with the new style water filter was no problem...twist to the left, drop the old filter, line up arrows on housing and new filter, twist to the right and done.

Ice maker was always crusing ice. There is a spring deflector wound around the actuating rod towards the back of the ice dispenser. Pulled the ice dispenser out, slid the damaged spring off, and slid the new spring deflector on making sure to engage the actuator rod to restore it's action. Easy fix.

replaced with new connector and it worked great. also replaced the water filter and that was super easy!

Pulled new tubing to the tank and put a union about 8 inches down from tank to new tubing. Great repair. Parts not readily available locally.

1. Slide out refrigerator away from wall.
2. Unplug refrigerator electrical cord.
3. Slide out refrigerator further to be able to get in back of.
4.Turn off water control going to refrigerator.
5. Clear top shelf around water filter area, remove water filter.
6. Remove water filter cover housing lid by lifting off.
7. Using a ¼" nut driver, remove two screws attaching water filter housing.
8. Go to back side of refrigerator, & remove 2 screws from the silver cover plate of MWD manifold water line unit.
9.Using ¼" nut driver, remove lower cardboard cover that protects the motor & fan area.
10. Clean motor & fan area with old tooth brush gently, & vacuum dust off.
11.Using (2) ½" open end wrenches, loosen & remove both water lines.
12. Go to front inside of refrigerator. Gently pull out old water line manifold assembly, you may have to twist it some to get the protective sleeve out of the hole.
13.Insert new water line manifold assembly into the hole, when it gets to mostly in, gently work the protective sleeve through the hole.
14.Position the new manifold water filter housing into place & reinstall 2 screws. Do not over tighten.
15. Go to back side of refrigerator, gently push down on protective sleeve so you then can replace silver cover with 2 screws. Do not over tighten.
16. Remove old tape that was originally holding water line tubings.
17.Connect water lines to water supply lines, using (2) ½ " wrenches. Tight, but not over tight.
18. Re tape water lines to back of refrigerator, using a strong tape like duct tape in an orderly fashion.
19. Turn on water supply, check for leaks.
20.Re install black cardboard piece on lower end of refrigerator.
21. Plug in refrigerator.
22. Install water filter inside of refrigerator. Install cover over filter housing.

I took the part out of the package and placed it in the recessed water dispenser/ice maker cavity. Done!