PER4310BAW Maytag Range - Instructions

unscrewed element from oven, traded wire connections to new element, screwed new element in - saved myself a $75 service call

we removed the back I had my dad help me so he removed the wires while I removed the screws on the inside. When I received the part he also helped me replace it by putting on the wires while I put the screws in. Remember to disconnect from electricity.

First I fliped the curcuit breaker to eleminate power to the stove. Then removed the 2 screws that hold the element in place. Then carefully pull the element out and disconnect. Installed new element to connectors and gently pushed back into the stove housing. Secured with the removed screws and turned back on the curcuit breaker. Turned on the oven and it worked like a charm..

Went down stairs and turned the breaker for the oven off. Opened the oven door, took a phillips head wrench and took two screws out of the back of the oven that held the element in place. Slowly pulled the old element toward me. It seemed to catch on something in the back of the oven on the other side of the oven wall, so a jiggled the old element a little and it came out towards me with a mechanical connector and a wire attached at both ends of the element. I slipped the connctors off of the element and attached the connectors to the new element. Carefully slide the new element back through the holes and put the screws back in the small plates attached to the element. Went down stairs and turned the breaker back on. Turned oven on and it heated up even quicker than the old element.

1) removed heating elements. 2) removed drip pans. 3) installed new drip pans. 4) reinstalled heating elements

Removed old element, pluged in new element.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes

I shut off the breaker in the fuse panel for the range ( recommended)
I had to unscrew the two mounting plates, unclipped two wire connectors.
Reconnected the two wire connectors ( pull off, push on)
Done
Flipped on breaker and was baking in less than 15 minutes.

Turned off the circuit breaker. Removed two screws - pulled the element out enough to get to clips connected to power. Removed old element - installed the new one. Replaced the screws, then turned the circuit breaker back on. Stove was repaired.

Remove burner elements. Remove old drip pans. Thoroughly clean stove top under drip pan edges, and under top cover. Install new drip pans. Install burner elements.
I never seem to be able to find the correct replacement drip pans at retail outlets in the quantities I need. Your parts identification, selection and ordering processes were simple and delivery was faster than I hed expected.
Thank you

Removed burner and then burner pan.Then replaced pan and reinstalled burner.

Easily removed the oven and had access to the rear in under a minute undid the 2 Phillips screws retaining the element and replaced with the new element I had ordered it was just so simple!

Thank you as you saved us calling out an expensive technician avoiding unreasonable time and costs expenditure

1) Unplugged the electrical cord and removed the oven door (only when easy); and, jockeyed the oven into better working area.
2) Removed about 9 screws holding rear sheetmetal backing plate to disconnect each of 2 electrical wires from the old element.
3) Removed 2 screws holding element to back of oven and 2 screws from small bracket supporting end of element to top of oven.
4) Replacement element was severely damaged. It was at the very bottom of a box 20 by 15 by 15.5 inches high with the large continuous bubble wrap stacked only on top. Each of the wire ends were sharply bent; one almost 180 deg. pointing in the opposite direction, and the other about 120 deg. The element itself was about 4-5 inches out of square. Using two large needlenose pliers I carefully bent each wire back to its proper place. Next I carefully exerted pressure on the element to gradually form it back to as near its correct shape as possible. (Only the inside of the shipping box showed the signs of possible damage.)
5) Installation- The element, from inside the oven, was placed back through the two holes in the rear of the oven and secured with 2 screws.
6) The bracket supporting the front of the element was slid onto the element and attached to the top of the oven.
7) Attached the 2 electrical oven wires to the 2 element wires, making sure there was good clearance to prevent any short circuit, plugged the oven cord in to 230volts, and checked it out with power to the broiler to give myself some confidence that the damaged wires would not quickly break. It seemed to work and I unplugged the oven.
8) Reinstalled the backing plate with the original screws, plugged oven back in, and moved the oven back to its place and replaced its door. It is working and my wife is cooking.

Shut off the power to the stove. Remove the two screws retaining coil
And simply pulled the coil out exposing the wire clips. The wires detach easily
Reconnected to the new coil, pushed the coil back in, reintalled the retainer screws and
Done. Time: ten minutes

I ordered the part and it came in within 2 days from fedex! Great timing. It took me all of 10 minutes to fix the coil at the bottom of the oven. Fixed the problem and had plenty of time to cook dinner before my husband came home!!
GREAT SERVICE AT THIS SITE! They knew the right part! And the instructions are very simple.

Thank you