PDT760SSF7SS General Electric Dishwasher - Instructions

Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.

I removed the old roller wheels and the new roller wheels snapped together and the simple instructions made the repair quick and simple..

Looked upm the problem it said door wasn.t closed so cause was the door latch. put in the new one no change so I bought a new dishwasher

I have them to the plumber who was reinstalling a poorly installed dishwasher. Parts worked perfectly

Bottom rack came complete with all racks. Only had to transfer the (2) side bumper guards,

Simply removed old gasket by hand, lined up center of new gasket (white dot was printed on the center of new gasket) with the tub latch and pressed new gasket into place. We have used the dishwasher about a dozen times since and hasn't leaked a drop.

Followed directions on YouTube

My heating coil was not working so naturally I thought I needed a new coil and ordered one accordingly. During the time it took to ship to me, I did more research and people suggested testing the coil with and ohmmeter for resistance as often times the coil is fine and it is the flood switch that is the problem. I got an ohmmeter and checked the old coil and it returned readings that were just fine (btw 15-30), so I returned the coil and ordered this flood switch.

Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.

The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.

However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.

Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...

First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen.
Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch.
I used pliers to grip the ring to take it out.
**Dry everything in the "well" where the flood switch sits.**
Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier!
Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!

Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!

Bought replacement rack transferred all the accessories from the old to the new. Mostly snap-in-place.

Needed GE Technician to install. Partselect.com had to send a second replacement rack because the first one was defective. When the second on arrived, IT TOO WAS DEFECTIVE. After the Tech tried to install the second replacement, he was forced to remove a part from the original rusted rack in order to get the 2nd replacement to even stay in the rails of the machine. Tech was great, but the Partselect.com parts were unusable as sent.

Read up on part at manufacturers web page and installed replacement correctly.