First, drain as much water as possible using a shop vac or siphon. Unscrew two plastic lugs and food screen to release the metal *disk* found inside the dishwasher at the bottom. Then, remove the grey retainer ring found under the food screen. Using the nut driver, remove two screws from the white plastic retainer ring at bottom the flood switch. I used pliers to grip the ring to take it out. **Dry everything in the "well" where the flood switch sits.** Now, remove the bottom front cosmetic panel. This exposes the underside of the appliance. Locate the flood switch wire underneath and gently pull down the small black plastic tab which holds the wires in place. This allows more movement to make your job a little easier! Pull up on the flood switch and simply unplug it and swap in your new switch! Replace everything as you found it, don't over-tighten your screws, and make your kids load that sucker! Hope this helps, and have a beautiful day!
My heating coil was not working so naturally I thought I needed a new coil and ordered one accordingly. During the time it took to ship to me, I did more research and people suggested testing the coil with and ohmmeter for resistance as often times the coil is fine and it is the flood switch that is the problem. I got an ohmmeter and checked the old coil and it returned readings that were just fine (btw 15-30), so I returned the coil and ordered this flood switch.
Anyone reading this debating between buying the coil and switch can save themselves a lot of trouble/time/money by removing the coil and testing it first.
The installation of the flood switch is fairly simple. There's a great video on Youtube for it (titled "GE Dishwasher not Drying Dishes - How to Replace Bad Flood Switch:), so I won't walk through the step-by-step on it.
However, one word of advice is to be careful when installing so that you don't let the o-ring on the switch slide down the connector/wire once you connect them or you'll get a slow leak into the catch pan at the bottom.
Also, if this if your first repair on a GE Dishwasher then get to know the unit while you have it pulled out. It won't be your last repair based on my experience...
No boost in water temperature; water temperature during wash cycle not hot enough; dishes not drying
Had to trouble shoot to isolated the true fault condition. Checked heating element was good Researched symptoms on YouTube Removed and inspected float switch part Ordered and replaced part.
Took out 2 screws that held machine in cabinet. Pulled out dishwasher about 4 inches. removed old latch and disconnected electric connection. Put in new latch, reconnected electric connection, replaced screws, pushed machine back in cabinet, replaced 2 screws that hold machine in place. Works like new!
Wanted to replace original rusted top rack of dishwasher
Needed GE Technician to install. Partselect.com had to send a second replacement rack because the first one was defective. When the second on arrived, IT TOO WAS DEFECTIVE. After the Tech tried to install the second replacement, he was forced to remove a part from the original rusted rack in order to get the 2nd replacement to even stay in the rails of the machine. Tech was great, but the Partselect.com parts were unusable as sent.
I replaced the Flood Switch Part Number: WD21X10519. I found that be removing the bottom front cover under dishwasher door, there was a small black plastic clamp holding up the wiring cable. By disconnecting the clamp, it gave me a few more inching of wire inside the machine, which made disconnecting old flood switch easier. It also help in installing the new flood switch. Then finally i reinstall the clamp cable under the machine to finish the job.
dishes were not dry at end of completed wash cycle
Followed the instructions on the video, it was pretty straight forward. It was helpful to know what to expect before hand like removing accumulated water in the drain before removing the flood switch so as not to have that water drain under the dishwasher. Knowing to have a nut driver with magnetic tip was helpful in removing and reinserting the screws. all in all it was pretty easy repair.
Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...
