PDT750SSF0SS General Electric Dishwasher - Instructions

Took cover of door off. Removeddoor from frame 1st. Lift door off of hinge. Disconnect door from springs. Unscrew bottom screws at base of door. Lift front cover(actually slides down) remove old part replace with new.make sure unplug door from main body.

-Disabled power.
-1/4” nut driver to take off kickplate.
-Unplug wires harness to door
-Dismount dishwasher from cabinets and pull out 4-6 inches
-uncouple spring pulley from door hinges.
-Open dishwasher door about 4 inches and pull out and up to remove
-Lay door down and remove 4 -T20 star bolts and two 1/4” bolts from door hinges(the door hinge has four bolts, but only remove one from each hinge that connects to the inner plastic door)
-remove vent cap and push up on interior plastic door casing to separate outer and inner door.
-Unbolt the soap dispenser module via 1/4” bolts and replace with new module. (be sure to line up module and gasket properly, installing 1/4inch bolts crossways, slowly tightening each bolt for a perfect seal).
-Reassemble the inner/outer doors and reattach to dishwasher in reverse order.
Be sure to plug the doors electric harness and kickplate.
-Plug the dishwasher back in and run it through a test.

I recently replaced the user interface, which took about 30 minutes. A week later replaced the soap dispenser module, which took 20 minutes. Disassembling the door was easier the second round.

I would read this project very easy for somebody with technical skills and easy with no prior skills

I replaced the flood switch following instructions shown in readily available YouTube videos. In short, you remove the coarse and fine filters, then take out the bracket holding in the flood switch and finally the switch itself. After replacing the switch, the dishwasher works normally again.

Simply twist on the new part/filter.

Popped old bracket off with screwdriver, with a then easy installation of the new part.

Unscrew the upper and side holding screws. Move dishwasher part way out. I didn't need to disconnect the water or electric. Make sure the electricity is off. Remember your working around water. Take off the bottom plat removing two screws, Remove broken cable pulley and replace new. Buy two since your their you might want to replace both. Have fun! It's duck soup.

Replaced motherboard, parts select,very helpful in helping diagnose problem! Exchanged parts, credit account after returned parts. Great customer service All good stuff! They brought their A game for this diy-er...

1. Turned off circuit breaker
2. Pulled out dishwasher
3. Disconnected switch and popped out switch
3. Popped in new switch and connected
4. Pushed dishwasher back into place
5. Turned on circuit breaker
6. Turned on dishwasher and it worked

Very straight forward. After removing the power source the dishwasher was pulled forward enough to access the the door hinge springs. Then the door could be removed and the inner skin separated to access the the dispenser mounting screws.

Looked up the replacement part on YouTube, watched a video and followed the instructions. Part ordered was the correct part and the video showed how to access for replacing. Watched a different video for hooking up the disconnected springs that allow the door to lower and close smoothly. Whole process for repairs was less than 30 minutes.

Removed two latch screws and one electrical connection, Removed
two screws that hold D/W to countertop, pulled D/W out enough to remove the old latch, install new latch, push D/W back into place, rescrew to counter top and rescrew the two latch screws. This problem happened since new, had repairmen twice and they did nothing but move the dishwasher stating it needed alignment, never mentioned this easy repair....

Tub gasket was a piece of cake, remove/replace by push in. Bottom door gasket was PIA. First you need to remove the door. Then, since the old gasket is held in place with a plate that is riveted together, you must drill out the rivets. Then you can install the new gasket. But first, you must use tap to replace rivet with threaded screw - unless you can find teeny tiny rivets!

Followed troubleshooting procedure to determine that defective Flood Switch caused the problem and not the Heating Element. Replaced only the Flood Switch. I also replaced a deteriorated door gasket.

De-installed dishwasher from cabinet, removed door, and tipped unit over with back of tub resting on floor.

I followed the document referenced here for the troubleshooting and repair procedures: GE Appliances Technical Service Guide, 2012 GE Dishwasher, 31-9226.pdf available on web.

Super easy repair, just removed the old latch and replaced it with the new one.

The old gasket pulled right out with no tools needed,
The new gasket went in the same way.

Results:
It did help on one side, but the bottom gasket also needs to be replaced it has a couple of tears one on each end.

Next Steps:
When the bottom gasket gets here I will replace that and it should be as good as new.