All Installation Instructions for General Electric Range PCGB940ZEJ1SS

oven post mini explosion sounding

the flame spreader through the years, developed a hole above the glow coil causing the above trapped gas between the oven pan and spreader to ignite. by replacing the flame spreader the problem is gone and is now working properly. thank you, parts select for being there when i needed the part and also being reasonably priced. mike marino

Parts Used:

DEFLECTOR OVEN

Mchael J. from Chesterfield, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

14 of 23 people found this instruction helpful.

Was this instruction helpful to you?

Gas oven was not lighting (bake only)

Repair was very easy. 2 screws to remove the bottom cover inside the oven. 2 more screws to remove the igniter. Cut the wires to remove it from the back of the oven. 3 screws to remove the back cover. Un-clipped old igniter , pushed new one through the hole (from inside the oven). Connected and re-applied screws. Worked like a charm.

Parts Used:

IGNITER GLOWBAR

Jerry from MACOMB, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

9 of 9 people found this instruction helpful.

Was this instruction helpful to you?

Grate to replace griddle

Remove griddle insert grate

Parts Used:

CENTRAL GRATE

Barbara from LOUISVILLE, KY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

10 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Missing grate foot / bumper

Put in a new foot / bumper. That's it.

Parts Used:

Burner Grate Foot

Irene H from HENRICO, VA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

9 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Warped burner

Set the burner in place

Parts Used:

Range Surface Burner Head

Outer Burner Cap

Ray from LEESVILLE, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Original burner cap was chipping; must have been dropped somewhere along the line.

New burner cap replaced old; just placed over burner; no tools required.

One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.

Parts Used:

Burner Cap - 15K

Mitzi from Briarcliff Manor, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

8 of 15 people found this instruction helpful.

Was this instruction helpful to you?

Hole burned through deflector oven and metal dropped onto igniter and burned it out

Removed bottom shelf from inside oven, turned it obj and replaced the oven deflector with only a screwdriver

Parts Used:

DEFLECTOR OVEN

Scott from ARDMORE, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

One burner would not light from spark. All other burners lite with spark.

First I checked that the wire and sparker was working by switching the wires on top of the range. I did this by pulling out the sparker switching it from the back working burner on the same side. The same burner would not light so I knew it was not the sparker.

Then watch a bunch of videos and found this gal to be the most helpful on how to take apart my exact stove.
Go here: https://www.youtube.com/watch?v=WRGfuhUzEaY

I did not take everything apart like she did. I ordered the spark module and just replaced it following her method to take off the back, switch the wires to the new module, then put everything back together again.

All burners have been working perfectly since the fix.

Parts Used:

Spark Module

Thomas from DEARBORN, MI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver

4 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Large burner cap finish was damaged

Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.

Parts Used:

Burner Cap - 15K

Richard B from CLARKSBORO, NJ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

3 of 4 people found this instruction helpful.

Was this instruction helpful to you?

the griddle was scratch up

just replace the griddle with the grate.

Parts Used:

CENTRAL GRATE

Betty from PHILADELPHIA, PA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Original Grates and Reversible needed replacing. The replacements were a perfect fit.

Did a search and found PartsSelect.
Inserted the model number of the GE Profile Gas Range.
Located the the needed parts, and added to the 'shopping' cart.
Then purchased, then waited for delivery.

Parts Used: