P2S930YP1FS General Electric Range - Instructions

Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.

I got a qualified repair person in to do the repair, but he had too much trouble getting the repair parts: left and right oven door hinges. The whole thing looked fairly easy when the hinges arrived so I decided to tackle the problem myself. Fortunately, I had all of the necessary tools, including a TORQ screwdriver. I got the door easily disassembled and installed the new hinges. I had a little trouble putting the door back together. Unfortunately, I had failed to take pictures with my iPhone as I disassembled the door, so I was left with a bit of guesswork on this one piece of molded plastic. I guess I got it right as I was able to reinstall the door and everything is working just fine.

ordered over the phone a new temp sensor. Un plug the oven, take off the back, open oven and unscrew the temp sensor, pull the sensor until the elec connector clip comes through so you can unclip the old sensor, clip on the new then pull the line back and re attach the sensor to the ovn. Plug in the oven.
Pretty simple, just hard to work inside the oven. I unclipped the sensor line outside the oven to make sure it would come apart first before I was working inside the oven.

My stove didn't seem to be getting enough power for the oven to heat up and the burners to get hot enough. When I checked the connection of the electric cord I found that one of the 3 terminals that the plug connects to was broken off. When the new part came I removed the old part by first disconnecting the 3 wires [black,white(ground),red] and then using a small but long 1/4 socket (that I found at Lowes)I removed the 2 screws that held the old part to the stove and the green screw under it holding the flat copper piece that also connects under the white ground wire of the part. I mounted the new piece on with the 2 1/4 screws. The new part comes with a piece of copper that is for grounding the part to the stove. When I compared it to the old part it was a little different. I first screwed the copper piece onto the stove (under the part) with the green screw then I screwed the white wire over the copper piece to the center terminal(you have to make the hole of the copper piece line up to the screw hole). I connected the other 2 wires and then connected the electric cord to the new terminal block and then put the back cover back on the stove and plugged it in. The clock came on I turned on the four burners they all got hot and red. I turned on the oven the element on the bottom got red I then turned on the broiler the top element got red. My stove is fixed.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

Replaced new light housing.
Thanks to you guys for the prompt response

Threw the old one out - plugged the new one in. Steak came out just as ordered - medium rare.

It only required placing the new burner in the proper location.

Replace existing grate with a griddle. Lift off existing grate, place griddle in its place

Replaced it

Turned off circuit breaker, Then pulled out range, straight out and away from wall and cabinets. Layed braket on flooring and moved stove back in to make certain it aligned with range rear stands. Moved range back out, marked holes in braket, screwed in screws to anchor bracket. Pushed range back into placed against wall. Tried to |"tilt" range by pulling down on door after opened - range was held in place sre

plug in thermistor when needed

I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections periodically as to avoid another situation like this .

Replaced the Oven light housing. Unscrewed the two screws that hold the housing in place. Pulled out the housing and disconnected the wire tabs from the light housing tabs. Slid the wire tabs onto the tabs of the new light housing fixture. (Each tab is fitted to the tab in goes on so they can not be mixed up) Pushed the housing fixture back into place and screwed the housing into place.