All Installation Instructions for Frigidaire Refrigerator NFTR18X4LB7

You have sent the wrong part for the THIRD time. You have sent aaccess cover that is TWO INCHES too short. It does not cover the opening, and you will not answer your phones.

There is no way to complete the repair with the wrong part, You have had my order since June 22nd, 2020 and the incorrect part arrived October 27th, 2020. You charged $7.79 plus $1.06 tax and $9.95 shipping. Please refund the entire amount including the shipping, since I did not ask you to ship the incorrect amount.

Parts Used:

Access Cover

Jane from EAST JORDAN, MI
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Nutdriver

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Handle was broken and ripped off the front of the refrigerator

Very easy installation. I took the original screws out of the door, set the new handle in place and screwed it on. Sooooo easy

Parts Used:

Refrigerator Door Handle Set (2 pieces) - Black

CAROL from MESA, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken door handle

Took out old screws, removed broken handle. Put new handle in place, used old screws. Super easy!

Parts Used:

Refrigerator Door Handle Set (2 pieces) - Black

Marie from EASLEY, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Broken handle again.

Install the new handle was very easy. These handles are no doubt made very cheap since this is the 3rd one I replaced in 15 years.

Parts Used:

Refrigerator Door Handle Set (2 pieces) - Black

Mike from CINCINNATI, OH
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

refrigerator crisper pan broken

replaced it

Parts Used:

Refrigerator Crisper Pan

DONALD from TOPEKA, KS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

2 shelves were broken and missingg

I (female) fixed it by just inserting the brackets. Easy as pie. I was so happy that they fit.

Parts Used:

Door Shelf Retainer Bar

Gabrielle from DERBY, CT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Bar had broken

Simply replaced by hand. No tools necessary

Parts Used:

Door Shelf Retainer Bar

John from BRONX, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

replace broken shelf protector

simply put the protector shelf bar on shelf !! easy

Parts Used:

Door Shelf Retainer Bar

Mary from EDMONDS, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Gasket was damaged everything inside would freeze

Pulled the old gasket out and pushed the new one in.

Parts Used:

Fresh Food Door Gasket - Black

Earnest from BOWDON, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Had a broken part in the door that holds condiments in

Removed broken part and then snapped in new part

Parts Used:

Door Shelf Retainer Bar

Janette St from KALISPELL, MT
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Freezer worked, refrigerator didn't. Ice build up on coils.

Unplugged refrigerator. Emptied freezer and removed ice maker and cover, need to unplug fan. Defrosted coils with hot water. Cut wires to thermostat as close to it ad possible to leave extra wire in case of an error. Stripped wire in new thermostat and put in shrink plastic then the wire crimp connector joining both light blue wires making sure wires were in before crimping them. Repeated with other dark blue wire. After used the heat gun to shrink the protective white tubing. The only thing i found not satisfying was tge tubing. It was too wide and too small. When i shrunk it did not cover the whole connector and was loose. I had to use a glue gun to cover both ends of each wire connector. Hope this helps other users.

Parts Used:

Defrost Thermostat

Salvador from SANTA ANA, CA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Coils frozen over. Refrigerator not cooling

I cut wires from bad thermostat and removed it . Stripped wires and crimped connectors on new thermostat and wires from old thermostat. Used heat gun to seal sleeves over connectors. Very helpful video from this site Thanks, you will be my go to parts supplier from now on!!!!!!!!!!!!

Parts Used:

Defrost Thermostat

Robert from MONTGOMERY, IL
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

Noisy condenser fan

Remove lower cardboard refrigerator panel. Carefully pull existing cracked fan blade off of the motor shaft and replace with new fan blade. Reinstall cardboard panel.

Parts Used:

Fan Blade

Ben from FRANKLIN, TN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Refrigerator did not cycle

Installation was fairly straight forward. The major complaint is that the problem returned 2 weeks later. I don’t know if I care to re-invest in another switch.
Now what?

Parts Used:

Cold Control Thermostat

JACOB from YOUNGSTOWN, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Door switch was no longer making my light go on when door opened

I used the youtube you provided. It was pretty straight forward, but I had to make a trip to the hardware store for a bit (hex wrench) to remove the hex bolt head style screws. I was only expecting to need phillips or flathead. I managed to remove one with a set of pliers, and the brought that example to the store for size reference when buying the bit to fit my black and decker drill. The rest was easy.

Parts Used: