NE6813 Dryer - Instructions

My husband got the part within 2 days of the order and replaced the leaking pump within a half hour. The repair was very quick and easy for him and your company's prompt delivery prevented my floor from getting wet everytime I did a load of laundry. Thank you and we will continue to get parts from your site in the future--hopefully we won't need to anytime soon. but we know you are there if we need to repair!

It was the first time I ever ordered parts online or even attempted to repair a washer. You all have made finding and ordering the right part very easy. I got the part in 2 days even though I used the cheapest shipping option (5 to 7 days). I turned off the water, removed the water lines so I could lay the washer on its side. No tools were needed to remove the water pump, just two clips held it on. I put the new pump on, hooked up the water and washed a load that night.

plires took off the two hoses , on clip the two snap clips . pulled out the old pump . put the new one in cliped in the snap clips in & hook the hoses back up

Pull Washer out, Flip to the right on it's side. Pop two Metal retaining clips, squeeze hose clamps with pliers. Remove pump, sand shaft with dremil or 80 grit sand paper. Replace with new pump. Easy! Push washer back and attach hoses and power. Done 15 minute repair

First, we took the pump off and found that it was leaking. Ordered the part on line. The part arrived in four days as scheduled. The small pump was easy to replace with screwdriver and pliars.

I press using the plier the spring retainer to removed the two hose from the defective pump.
I used screw driver to removed the two retainer.I pulled the pump away from the shaft of the motor. Replaced with new pump, align to the motor shaft and return back the two retainer. It is easy and its good to have my parts right on time.

Removed water supply hoses and took drain hose out of drain. Unplugged electrical cord. Turned washer over to see and reach pump easily. Flipped clips holding water pump. Moved hose clamps back on inlet and outlet hoses. Wiggled hoses off pump. Placed new pump and flipped clips back in place. Wiggled hoses back onto pump ports and replaced clamps to hold. Turned washer upright and reinstalled. Using channel lock pliers to move hose clamps was the hardest part.

Removed the four screws from the control housing. Disconnect wire to machine housing. Remove the two clips connecting the machine housing to the back. Remove washing machine housing. Pump is located right in front. Disconnect hoses, remove and replace pump, reconnect hoses. Replace the machine housing. This was the hardest part if all trying to reinstall the housing.Once you get the machine housing in place correctly, put everything back together. You just saved about $125 in fifteen minutes.

Frist I removed the two water hoses going to the pump. Second releaseed the two clips holding the pump , it came right off the motor shaft.
Third, put the new pump on the shaft, put the clips on last the hoses good to go.

Removed the two spring clamps from hoses; removed hoses from pump. Removed spring clips holding pump to motor. Had to pry pump off of motor shaft due to rust on shaft end. Sandpapered rust off of shaft and then lubed same with oil and new pump slid easily onto motor shaft. Re-snapped spring clips to hold pump onto motor and then reinstalled hoses and their spring clamps. Whala, end of story, job well done.

1) Disassembled the lid
2) Took the front Panel off (the old water pump was in the bottom left hand corner in plain site).
3) Used flat head screw driver to gentle pry the top and bottom water pump fasterners.
4) Used pliers to remove top hose camp. Note this is where I discovered why everyone says to put the washer on it back. Water came rushing out. Luckily no damage to the motor.
5) Used pliers to remove the bottom hose clamp.
6) Put everything back together Total time <30 minutes.

Unfortunately, the water is still not completely draining. I am now looking at the hoses for obstructions. Any other suggestions?
Thanks

I unplugged the washer, put a towel down, leaned it back and held it up with one hand while undoing the clamps with plyers. Pulled the two clamps off, pulled the pump, put the new pump on, reattached the clamps. Most of this with one hand while the other held the washer at an angle.

Disconnected power, water, and drain then moved washer away from wall. Put down some 2x4's to protect hoses and flipped washer on its back. Removed hoses with pliers, removed clips holding pump to shaft, and installed new pump. Reversed process and tested with just water be fire washing clothes.

laid washer on side, used butter knife to pry off spring clips. there is just enough room to get pump off the shaft .Unhook two hoses then install new pump.

First I watched the repair video. Then I pulled the power plug and shut the water off. I didn't have all the room available to remove the front and sides of the machine in my narrow hallway so I just slid it away from the wall and leaned it back against the wall and had plenty of room to do the repair lying on my side. $28.00 part and in 20 minutes all done. This is the second time this site saved me time and mucho money. Thank you. Leon B. from Massachusetts