All Installation Instructions for Norge Range N3137XRA

broke the igniter in the oven before I even got the oven installed

ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.

Parts Used:

Flat Style Oven Igniter Kit

june from wills point, TX
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

My oven door seal had dried rotted

I took pliers to get the old one off, and popped the new one back in its place, and it fit perfect.

Parts Used:

Door Seal

Anita from ELKTON, VA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

Old seal breaking off oven door. Oven not baking food well, wasting heat and fuel.

Used pliers to remove clips and old seal. Snap in new seal. DONE! Less than 5 mins.

Parts Used:

Door Seal

Mz from COLUMBIA, ME
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

1 person found this instruction helpful.

Was this instruction helpful to you?

igniter failed to ignite

Replaced the igniter by removing 2 screws, pulling on the wires to pull the connector in from the back thru the oval opening, screwing in the the new element, reconnecting the wires, pushing the connector back and that did it.

Parts Used:

Flat Style Oven Igniter Kit

Gino from ARLETA, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set

1 person found this instruction helpful.

Was this instruction helpful to you?

The oven bottom was warped and could not be positioned properly in the oven.

Removing the old oven bottom was easy...as it was already outside of its slots. Installing the new one was pretty easy. I placed the oven bottom in the front slots first...then the rear slots...no tools necessary.

Parts Used:

Oven Floor Panel

Tara from ALBANY, NY
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Simply remove and install new parts

Overall, it was painless and easy with zero problems

Parts Used:

GRATE BURNER

Jacob from LITTLE CANADA, MN
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

no spark on top burners

part was by the brolier drawer inside under stove removed 2 screws on cover/ part was attached to cover removed module line 1-2 fit/ had to use supplied disconects crimped on 4 burner wire leads/taped around module w/ elec. tape put back 2 screws finished. works now.

Parts Used:

Spark Module - Surface Burners

eric from winter haven, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Oven ignitor would glow but took 30 - 40 mins to heat

It took me 10 mins to replace the oven igniter and I did it myself. Oven is working fine now. I saved myself a $300.00 repair bill. Thank you for making the part available and saving me dollars!

Parts Used:

Flat Style Oven Igniter Kit

Catherine from Newton, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thermostat bulb was hanging loose

Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

Parts Used:

Range Thermostat Clip

Willi from Old Saybrook, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Oven did not ignite

Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..

Parts Used:

Flat Style Oven Igniter Kit

John from Racine, WI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven Ignitor went to ignitor heaven.

The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

Parts Used:

Flat Style Oven Igniter Kit

Brian from Pittsburgh, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

smell gas and sometimes a whoof on ignition

I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .

Parts Used:

Flat Style Oven Igniter Kit

Maynard from Knox, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Oven making whooshing sound and not heating up

Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

Parts Used:

Flat Style Oven Igniter Kit