Models > MVWX700XW2

MVWX700XW2 Maytag Washer - Overview

Sections of the MVWX700XW2

[Viewing 6 of 6]
Keep searches simple, eg. "belt" or "pump".
Lid Latch Assembly – Part Number: W10404050
Lid Latch Assembly
★★★★★
★★★★★
(35)
PartSelect #: PS3497627
Manufacturer #: W10404050
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the washer while the tub is spinning.
$45.21
  In Stock
Drive Belt – Part Number: WPW10006384
Drive Belt
★★★★★
★★★★★
(19)
PartSelect #: PS11747978
Manufacturer #: WPW10006384
The main drive belt is designed to ride on the pulley until the basket gets up to speed.
$33.51
  In Stock
Washer Drive Pulley – Part Number: W10721967
Washer Drive Pulley
★★★★★
★★★★★
(20)
PartSelect #: PS10057144
Manufacturer #: W10721967
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
$57.16
  In Stock
Tub Centering Spring – Part Number: W10400895
Tub Centering Spring
★★★★★
★★★★★
(8)
PartSelect #: PS3497596
Manufacturer #: W10400895
Tub centering spring
$9.92
  In Stock
Suspension Rod Support – Part Number: W10440729
Suspension Rod Support
★★★★★
★★★★★
(18)
PartSelect #: PS3502189
Manufacturer #: W10440729
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
$9.44
  In Stock
Drive Hub Kit – Part Number: W10528947
Drive Hub Kit
★★★★★
★★★★★
(23)
PartSelect #: PS6012095
Manufacturer #: W10528947
This drive hub kit (part number W10528947VP) is for washers. Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
$34.96
  In Stock
Washer – Part Number: WP3949550
Washer
★★★★★
★★★★★
(1)
PartSelect #: PS11742027
Manufacturer #: WP3949550
This part goes on the agitator retaining bolt.
$13.40
  In Stock
Touch-Up Paint - White – Part Number: 72017
Touch-Up Paint - White
★★★★★
★★★★★
(1)
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.44
  In Stock
Shift Actuator - 120V 60Hz – Part Number: WPW10006355
Shift Actuator - 120V 60Hz
★★★★★
★★★★★
(24)
PartSelect #: PS11747977
Manufacturer #: WPW10006355
This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.
$68.13
  In Stock
D-Shaped Knob Insert – Part Number: WP8536939
D-Shaped Knob Insert
★★★★★
★★★★★
(1)
PartSelect #: PS11746209
Manufacturer #: WP8536939
This insert is sold individually. Knob not included. Knob is sold separately.
$10.56
  In Stock
Hose Clamp – Part Number: WP285655
Hose Clamp
★★★★★
★★★★★
(2)
PartSelect #: PS11740613
Manufacturer #: WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$8.79
  In Stock
Lid Bumper – Part Number: WP9724509
Lid Bumper
★★★★★
★★★★★
(4)
PartSelect #: PS11747040
Manufacturer #: WP9724509
This gray and white washer lid bumper contains a rubber bottom and is sold individually.
$7.76
  In Stock

Questions And Answers for MVWX700XW2

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

10 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Teresa
    December 28, 2019
    My washer will not finish all cycles needed to complete normal cycle it stops when it gets to wash then lid lock unlocks and power light go off. I've tried unplugging it. Then plugging it back in. No
    For model number MVWX700XW2
    Hello Teresa, thank you for your question. It sounds like the lid lock isn't functioning properly. We would recommend replacing the lock PartSelect Number: PS3497627. Please enter the part number into the site for current price and availability. Good luck with your repair!

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Vanessa
    February 4, 2020
    On the normal wash cycle my washer will not drain and spin all the way. My clothes come out very wet .Most of the time i'll have to set it to the drain and spin to complete the cycle. What could be wrong with my washer.
    For model number MVWX700XW2
    Hello, Thank you for your question. If your washer will not spin out all water and clothes are still wet, the drain pump might be clogged with debris or possibly faulty. There could be a foreign object that is stuck in the pump and inside the drain hose. We hope this helps.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Jana
    February 8, 2020
    Washer will spin without clothes in it, but as it is trying to start spinning it clicks a bunch of times and then stops. Also makes a very loud noise when spinning, sounds like an airplane taking off.
    For model number MVWX700XW2
    Hi Jana. Sounds like it may be a bad motor or drive belt. Thank you for your question and good luck with your repair.

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Randy
    March 15, 2022
    I start my washer, the lid locks. After a pause, there is a loud humming noise that stops with a loud click. Then nothing happens, the display panel does stay lit.
    For model number MVWX700XW2
    Hello Randy, thank you for your question. It sounds like the lid switch might be broken. You can test this with a multimeter. Unplug the appliance from the electrical outlet before you begin. Set your multimeter to the lowest ohms of resistance and test your lid switch. If it does not read any continuity, then your lid switch is indeed faulty. Part number FIX3497627. We hope this helps! If you need help placing an order, our customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!

    Was this helpful?
    Thank you for voting!
    Related Parts:
    Randy
    March 16, 2022
    Responding to answer for loud hum and click question. I checked lid latch circuits for continuity, which i found on all wires. However i noticed that the loud hum and click was coming from the drive motor area.
    For model number MVWX700XW2
    Hi Randy, Thank you for your question. If the motor in your washer clicks and hums, the motor bearings are damaged or worn and the motor will need to be replaced. The part number listed under your model number for the motor is FIX11726282. If you need help placing an order for it, customer service is open 7 days a week and anyone will be happy to assist you. Please feel free to give us a call. We look forward to hearing from you!

    Was this helpful?
    Thank you for voting!
    Related Parts:

      Common Symptoms of the MVWX700XW2

      [Viewing 14 of 14]
      Will not agitate
      Fixed by
      these parts
      Show All
      Noisy
      Fixed by
      these parts
      Show All
      Pumps but will not spin
      Fixed by
      these parts
      Show All
      Shakes and moves
      Fixed by
      these parts
      Show All
      Will Not Start
      Fixed by
      these parts
      Show All
      Leaking
      Fixed by
      these parts
      Show All
      Will not drain
      Fixed by
      these parts
      Show All
      Spins slowly
      Fixed by
      these parts
      Show All
      Lid or door won’t close
      Fixed by
      these parts
      Show All
      Lid or door will not open
      Fixed by
      these parts
      Show All
      Burning smell
      Fixed by
      these parts
      Show All
      Will not stop filling with water
      Fixed by
      these parts
      Show All
      Timer will not advance
      Fixed by
      these parts
      Show All
      Will not fill with water
      Fixed by
      these parts
      Show All
      Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
      Lid Lock light blinking, machine will not start
      A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
      Parts Used:
      Shift Actuator - 120V 60Hz
      • David from Los Alamos, NM
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        30 - 60 mins
      • Tools:
        Nutdriver, Screw drivers
      302 of 375 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Defective lid latch - Cabrio Washer
      The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
      Parts Used:
      Lid Latch Assembly
      • William from Wakefield, RI
      • Difficulty Level:
        Very Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers
      81 of 97 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Noise on bottom of Washer louder as time went on. 1 1/2 years
      Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
      Parts Used:
      Drive Belt Washer Drive Pulley
      • Jerry from WALLA WALLA, WA
      • Difficulty Level:
        Really Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Screw drivers, Socket set
      63 of 81 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!