Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
This basket drive hub kit is a vital component in select washing machines, designed to connect the wash basket to the central drive shaft, enabling proper rotation during wash and spin cycles. It play...
This washer lid switch is a critical safety component designed to halt the spinning motion of the tub when the lid is opened. Its primary function is to prevent accidental contact with moving parts du...
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the ...
These parts are the replacement suspension rod supports for your washer. They are made of plastic and are approximately 1 ½ inches in diameter. This package will come with an 8-piece set of suspension...
This shift actuator is a genuine replacement component designed for top-load washing machines. It plays a critical role in transitioning the washer between agitation and spin cycles by shifting the tr...
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
$31.58
In Stock
Order now and your part arrives by May 31
Questions And Answers for MVWX500XW2
Ask our experts a question about this model and we'll get back to you as soon as possible!
7 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jola
April 7, 2024
Rusty lid. Is it better to buy a paint and fix it much cheaper?
For model number MVWX500XW2
Hi Jola, thank you for the question. Yes, you can remove the rust on the lid with sandpaper and then use touch up paint white, part number PS385132, which is much cheaper. It is better to build coverage with several coats of paint. We hope this information helps!
WHY IS LID LOCK LIGHT FLASHING AND MACHINE WILL NOT RUN?
For model number MVWX500XW2
Hello Bill, thank you for reaching out. We have researched your model and found that the issue could be caused by a faulty lid latch assembly, part number PS3497627. The point of the lid switch is for the tub to stop spinning when the washer lid is opened. Customer service is available 7 days a week if you need help placing an order. Glad to be of assistance!
After doing the diagnostics test, i figured out that the wash cycle is where it stops working. It is slow to start sensing but once it does, it is fine. What part do i need if my washer will not go into wash mode?
For model number MVWX500XW2
Hello Amanda and thanks for writing.
If your washer reaches the wash cycle and shuts down or refuses to work properly, the problem often involves water flow or electrical circuits. Check your water hoses to make sure there is no blockage.
If that is ok you might need a new electric control board PS11751598. We hope this helps. Please contact us anytime.
We replaced the actuator (remodeled part designed to keep water off of it). The machine seems to be "talking" to itself. Locks lid, starts to fill "growls" starts over, stops starts again. Still does not spin. Any suggestions?
For model number MVWX500XW2
Hello Elizabeth, Thank you for the question. This sounds like the Control Board that controls the functions and cycles is defective and may need to be replaced, PartSelect Number PS11751598. We hope this helps!
Once the sensor mode and the wash mode is conpleted and goes to the rinse mode, the washer then goes back to the wash mode and then stops. The gasket has water in it and doesn’t drain.
For model number MVWX500XW2
Hello Barbara, thank you for contacting us. Based on our understanding of the issue, we would suggest checking the control board, part number PS3653301, to solve the problem. We hope this helps.
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
