MSK27PFXAAA General Electric Refrigerator - Instructions

son did the work BUT ONLY AFTER- trying to order the part from Sears parts online, in which they never from the right part and i spent 1 and 1/2 hours on chat and finally gave up. THEN i called sears replair, made appointment for two weeks later requesting 1st repair time of the day, was asured the repair would take place between 8-12 and beacuse it was 2 weeks away it should be the 1st repair. The day of the appt I received a phone call at 11:38 saying they would be here about 12:20, I SAID NO THANK YOU< OUR AGREEMENT WAS BY 12:00. THen I got online typrd in water tank your company come up, showed photo, and price which i ordered it can in my son fixed it and all was complete within an hr.

Emptied hopper
Removed screws to remove auger from existing
This was so easy I impressed my wife

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

First, I had to remove the face plate where the ice and water was dispensed remove 4 screws holding the electrical circuits, disconnect circuits ,remove 2 screws holding soleniod and one screw holdin crank assembly. repace parts and screws.

Replaced dispenser flapper

1. Unplug the fridge
2. Removed the outer facing of the dispenser outside the freezer door. This is fairly easy, better with a tool (plastic scraper) that won't mar the finish.
3. Removed the plastic plate with labels -- water, ice, etc. This is done by sliding a small jewelers screwdriver into the slots on the left, middle and right in back of the plate. These are difficult to see without a flashlight.
4. Removed the four screws in the panel behind this plate.
5. Unpluged the large cable on the left side after the panel is freed.
5. Removed the rubber "dispenser" button. this just pulls off.
6. Remove the panel
7. Lift flapper up and remove. Clips hold this in.
8. Put new flapper in place.
9. Use reverse order to put back together.
Piece of cake. Ice maker no longer frosts up.!!!!

Firts I removed the food from the freezer. Then I used the cordless drill/screw driver to loosen the broken piece of plastic. I inserted the plastic shield and screwed the shield in place. The majority of time was spent removing and replacing the food from the shelf.

Finding the part was made so easy by this website. I wish I had done it years ago but because I am not handy, I didn't think I could do it. Reading how easily others did it convinced me to try.

Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.

Transferred ice supply to another freezer. Removed ice maker unit from freezer and studied assembly. Removed the 5 screws holding the bucket in place while keeping track of which screw went where. The only positional component to remember was the motor control pivot retainer. Wiggled and fiddled to remove the old bucket. Wiggled and fiddled to put the new bucket in place. Replaced the 5 screws, dumped the reserved ice back into the bucket, and returned the ice maker unit to the freezer.

Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.

The same as the vidio, very easy. Thank you

Super fast replacement, and the part was sent to us FAST and WELL-PACKAGED and REASONABLY PRICED! Thankyouverymuch!

Removed ice tray and set on kitchen counter .One small phillips scredriver to remove broken tab.
Attached replacement shield with screw, replaced ice tray. Probaly total of 5 to 10 minutes to find scredriver, do the repair & replace screwdriver where it belonged. Took more time to place order then do repair. Add a couple of minutes to unpack.and some more time to drop off cardboard box at recycle center.

Because of the way it broke I was not sure how it was attached until I read reply's from others who had the same problem. The instillation tip was greatly appreciated.

Followed the instructions and replaced the door recess.