MLE19PNAUW Maytag Washer Dryer Combo - Instructions

The door switch was easy to replace. It is located in the right bottom of the door and I popped out with my fingers. Follow the wire connectors from the old switch and remounted back in.

Unscrewed front panel. Pulled off unbroken wire connecter and popped switch and put new one in. Replaced front panel.

Replaced the heating element and both thermostats. Hope that takes care of problem! You tube was a tremendous help through video's.h

Just follow the video. The hardest part is getting the top to disengage from the clips.

Watched the videos for the repairs on the site. Took the back of the dryer off after unplugging the appliance. Removed the failed fuse and thermostat and replaced them both per the video steps. It took about 25 minutes for both parts and the dryer now works well.

I looked on Utube at some videos which helped a lot all told i replaced the bearings in the outer hub which was quite a chore as the bearings came out rather hard I used a steel rod about 18 inches long and a heavy hammer to pound the old bearings out they came out hard then I put the new bearings in very carefully as I had to tap them back into place and installed the seal and put the new shaft on the tub and slid everything back into place. The instructions that came with the new seal and shaft were very helpful I bought the new bearings from local implement dealer as they were not available with the shaft and seal didn't keep track of my hours probably about 21/2 to 3 hours

Several times I watched the video of "Steve" removing the old motor and installing the new one. Pretty much followed what he did. Faltered for a moment at the end reinstalling the drive belt as that was a blind procedure, done by feel. Hardest part was getting the spring clamps off the old motor; even Steve struggled a bit doing that part of the job on the video. But in the end, the dryver started right up and ran quieter than it has for months.

I ordered the wrong motor for my dryer PN PS3500892, the right one was PN PS11741125, the motor specs were the same but the shaft were different lengths and different blower fan and fasteners. Since I had the wrong motor in hand I worked with Parts Select to order the correct blower fan and fasteners for this motor. Got it all installed and everything fit as it should. even though this was a different part than I had before it saved me $100 by doing it this way, Thanks to Parts Select for helping me through this maze with me asking many questions about part sizes and fasteners. They did this all for my savings. Most parts places would not have gone this far for the customers benefit. Thank you very much Parts Select !

If you have the option to take a part the dryer before ordering the parts to track down the squeaking part, do so. In my case a squeaking part is still usable. Unfortunately the squeaking part was not the rollers or the belt depicted as a high percentage of the squeaking problems as noted on the webpage.My was the Idler Pulley. INSTALLATION of idler pulley, I started by watching the youtube videos, took pictures during the removal of the parts to assist in the installation. removed front panels parts, moved drum forward off the rollers, reached in and pulled the idler pulley to the left in order to remove belt. pulled the drum out. And with a flat head screw driver popped off the e clip (bought extra e clip just in case i lost it) reinstalled everything, BUT take note of the Idler pulley, it has one side bigger than the other BUT in the CLOSE UP VIDEO THE GENTLEMAN INSTALLS IT BACKWARDS. Not sure if this has a major effect on the pulley, but wanted to give it a heads up (your pictures will help you with this to keep track of how it should look at the end).

I followed the YouTube video for pulling the heating element to remove and place the thermostat. The actual thermostat removal and replacement was pretty simple. Most of my time was spent removing the front panel, pulling and reinstalling the heating element.

Unplugged the dryer (don't forget this step guys!!!)

Pulled the front off the dryer (4 screws) and swapped the motor out - take off the belt, pull the blower wheel (by removing the snaprigs and squeeze collar), then pull off the motor retaining clips... unplug the motor and install the new one in reverse. Took me less than 2 hours and my dryer works like new.

WAY CHEAPER than a new dryer!!!

removed front door, removed front panels, lifted top back, unhooked belt, removed drum and belt, removed blower housing front, removed squirrel cage, removed blower housing, unplugged motor, removed motor assembly , ..switched new motor to motor cradle ... reversed process.

My Husband did the repair. He had to take the entire dryer apart to get to the motor. Removed door, front pannel, drum. During this repair he also replaced the belt since it had cracks and since the dryer was taken apart. placed new motor in and put all back to gether many screws he had to remember where they all went. Have to be very careful with the felt liner around drum. we started dryer has never ran more smoothly. Two people recommended to put dryer back together.

Remove front of cabinet, hinge the top back, remove the drum and drive belt, unplug the motor, remove cover on blower, remove snap ring on end of motor shaft, remove motor mount hold-downs, remove and replace motor in reverse order

I removed the lower panel and control panel, then the front body panel. With those open, I removed the drum support and drum. I then removed the cover from the air guide, then unbolted the air guide from the motor assembly.

Then, I disconnected the wiring connector to the motor, unbolted the motor carrier from the bottom of the unit, and removed it. I removed the idler arm from the motor carrier, then unclipped the two clips holding the motor in the carrier.

At that point, while everything was out, I gave the carrier a thorough cleaning. I then placed the new motor, replaced the clips that hold it in place, and put everything back together in the reverse order of taking it apart.

While I was in the machine, since I had everything taken apart, I did also take the opportunity to replace the idler pulley and drum rollers proactively.