MED6000XG2 Maytag Dryer - Instructions

I saw a couple of videos to replace this but found a simpler way to replace the heating element on my dryer. DISCONNECT the POWER.
I removed the lower panel (6 screws). Dis-connected two wires; one going to the heat sensor in the back and the other to the switch at the front. Removed the two screws to the metal plate in front of the heating element. Slid the whole heating assembly out. Removed the screws holding the heating element in the housing. Removed the failed (open) heating element and installed the new one. Reversed the process for re-assembly.

Message indicated something amiss in the motor circuit. Followed Instructions in the on-board manual. Turned out to be the internal-bias thermostat, and the exhaust air thermistor both. Changed faulty parts, cleaned lint from the system and we are off and running again.
Thank You.
DW Pranger

You tube

I took off the back panel off the dryer. The idler pulley could be accessed on the bottom. It was a bit cramped but not too tough to replace.

Remove top, remove two front panels, remove rear panel to access drive motor release tensioner. Remove drum to access to heating element enclosure. Replace and reinstall after vacuuming all accumulated lent.

I googled the problem and determined that the thermistor was faulty. I found your web site from which I ordered the replacement part. The part arrived within a week. The replacement was not particularly difficult, but the space was very tight (without removing more panels and covers). I just kept at it and got it installed and the dryer works fine now. There are several pertinent videos on you tube, none of which were my particular model, but the combination of them led me to a successful installation.

Pretty easy repair and I am not very handy. I believe they engineer these machines so you hire someone to do the job. They could place that part in an area where it is easier to get to, like a door on the side or something

I ordered the part(and a backup) and had it in two days. 5 days less than ordering from sears.

The first thing I did was to watch the video from Part select on How to change thermostat cut off switch and the high limit thermostat fuse.I did not have a meter reader I just brought the thermostat cut off kit for about $ 32.00 dollars from part select and replace both part's and my dryer still was not getting hot so back to part select video's I looked up the video on replacing the heater element and I ordered one for about $ 97.00 with shipping I replaced it and put it back together and it worked it took just a few hours . I would like to give Avery special thank to part select for the video help and for having the parts for a great price again thank you so much.

Followed your video for replacing the Tension Pulley, Drum Belt and Drum Rollers. Models were not exact, but instructions were very clear and detailed enough for a "computer geek" to do the repair myself (with some help from my wonderful wife). Live in Ohio, parts came from Kentucky and I had them the next day! The dryer is almost 10 years old. Running great now. Thank You!

Lint can build up inside the dryer, and can cause a fire in EXTREME cases. If your model has a back panel that exposes the entire chute, this job is much easier. Unscrew the chute from the machine to remove it. Inspect and clean all the lint out, especially the bottom, next to the fan blower. The other version machine has a panel at the top that is welded on. Remove the two screws at the top corner of the rear bulkhead, where the chute is. Gently pull this inner panel away to free the top of the chute from the rear top panel. Then pull the chute down and out. Follow the reverse to complete the job.

Use the adjustable wrench to remove the water line. Remove the dryer vent line. Take off the screws on the main back panel, the screws connecting the top. Place both off the side. Unscrew and remove the parts connecting to the heat line located on the left side. Remove the front unit screw attaching the heat line to the bottom of the dryer. Remove the four screws connecting the top and bottom of the heat line together. The two on the left side is a huge pain, make sure you have small hands to be able to reach on the side of the line. Pull the bottom of the heat line loose. The heating element is inside the line. Replace element and put everything back in the order it was removed.

Pulled the back panel off with nut driver , reached in removed belt from pulley , disconnected the spring , removed the the 1 bolt holding the bracket .
Put the new one in , in reverse order . Very simple , maybe 15 minutes total . While back is off , shop vac out any lint !!

Followed the instructions on your video.

Removed the lower front cover of the dryer. Removed the lint filter and removed the cover from the air duct by removing two 1/4" bolts. Removed the two 1/4" bolts retaining the thermistor. Installed the new thermistor and covers.