MED5630MBK0 Admiral Dryer - Instructions

I saw some videos suggesting you remove the back panel.Then I saw a video where only the kick plate was removed and the element was removed that way.
I removed both the back panel and kick plate.At first I thought I was wasting my time however once I got started I was glad I removed both back and front.
There was a significant amount of lint in the bottom of the dryer which made it easier to remove.
It also made it easier to remove the heater element.
I hope this helps.

Removed the back panel and saw that the idler pulley was worn out. It only took me 5min. To replace, it was very easy to replace.

Remove backing very easy (approximately 12 8mm screws).
Thermostat on left side facing the back. 2 8mm screws . Thermal fuse slightly further towards front of dryer but still accessible (caution longer arms needed). Unscrew first them release safety clamps
to unplug (be gentle have patience). Place all back same as removed and it worked!!

I had already taken the coil out of the heating housing to check for a break in the heating element. I took this time to vacuum out all the lint inside the cabinet. I slid the new coil into the housing and reattached the wires. Plugged the dryer back in and turned it on to make sure the coil heated up. It worked so I put all the screws back in and fastend the front back on and were in bussiness!

unplugged from elect power.took off front lower panel.removed heater heat shield w/1/4 in nut driver,could see heat element. it looks like at thin metal twisted phone cord. i used a continuity tester to establish if there was a break in it. there was. i removed 2 1/4in screws on the right side of the element,marked wire placement slid out old element & slid in new one put screws back in connected wires,put heat shield back on . tested dryer ,ok good to go put on front cover.!!!!! PS sears parts wanted 15$ more

Half of my pulley was broken off so there were no wrench flats to take it off. I was able to remove it using Channel Locks and the 7/16 wrench shown in the video.

Hint: Use a one gallon ice cream bucket to hold up the drum while connecting the belt. It makes it much easier and gives you more clearance.

Took off back of dryer Undid belt from belt adjuster pulled and took off adjuster put new one on redid belt and put back on dryer. Done

My husband said it was very easy and quick. We will recomend your site for sure.

So simple.... I have no idea how to fix anything but I took a crack it. Looked inside and pulled out the resistor. I noticed the coil was broken so I replaced it with a newn part and reinstalled it. Worked like a charm. Saved myself alot of money!!!!

The dryer stopped heating. Took the front lower panel off of the dryer and obtained the troubleshooting instructions stored there. Used an ohmmeter (most volt meters also have an ohmmeter) and tested all the electrical components one by one (thermostat, thermal fuse, heater coil - following the troubleshooting instructions provided with the dryer) and found that I didn't have any resistance across my heater element. Removed it and sure enough there was a break in the heater coil. Ordered a new heater element from PartSelect for less than $50 and replaced it myself. Saved myself a good bit of money repairing my dryer myself. It was very straight forward and easy. If you can follow easy to read instructions you can do it.

we received the two heating element wires in 3 days and connected the heating element with no problem works great.

this was very was very easy. But I deviated from the You Tube instructions. One to release the motor pulley. I needed to use 2 adjustable wrenches for a longer lever. I needed to use a hammer to help release pulley. Second to remove the dryer cable I needed to use a small screw driver to aid in the release. ---- the part from the company was a perfect fit.

Took the front part of the dryer out, released tension on the idler pulley, took the drum out, and remove the old drum seal. Make sure you remove the old adhesive with sandpaper or wire brush. Put the new adhesive on the seal, not on the drum. Adhesive is very runny. Seal may need to be stretched to fit the drum. Set the seal on the drum, let sit a few minutes. Put everything back together.

Started at the top by laying back the control panel, then I removed the top panel, then the front panel, next the drum and the broken belt. before I put it back together in reverse order, I vacuumed the inside of the dryer and the exhaust vent

Removed top and back covers. Placed new pulley and retaining clip in place. I had to remove a couple of drum supports to put belt on. Probably didn't have to remove top.