MDB8750AWQ Maytag Dishwasher - Instructions

Remove inside cover and eight screws. Unplug two electrical connections.

Very easy to replace the roller. First I removed the stop on the top slide. Then I unsnapped the old roller. The new roller just snapped right in place. Then I put the drawer slide back on.... Took less than 5 minutes.

1.Disconnected the electricty 2. pulled the dishwasher from under the cabinet 3. tilted the washer on it's face (water supply was long enough and did not need to disconnected.)4. unscrerwed the 2 plastic nuts that hold the heating eliment in place. 5. tilted the dishwasher back upright and removed the old heating element. 6.put the new part in place had a helper tilt the washer forward while i tightened up the two plastic nuts to hold the part in place.7 reattached the elecrtic conectors to the heating element. 8. pushed the dishwasher back in place. 9 hook the electricity back up. During step 4 i had to remove the electric connectors from the old heating element.

Switch was not the same switch as what was in the unit, similar but switch was normally closed instead of open, so had to take the switch apart and change sides with the contacts! should be the same, but was not, so in the end worked fine after an adjustment!

The repair was much simpler than I had anticipated. I just started removing screws, remembering what screws went where, and carefully removed the parts I needed to until I could get to and remove the filter unit. Installing the new unit was a snap, then it was just a matter of putting everything back together.

The original piece is 100% plastic (with metal shields only to prevent burning). The bushing of the arm was badly worn out in one side. The arm was no turning properly or at the end no turning at all. I decide to drill the new part in order to fit a brass bushing inside (1/4" ID, 5/16" OD, about 2" long). I expect it will last considerable longer. I would say this is a typical "defective by design" problem.

Unfortunately, my experience was unlike that of the other people who posted. While everything did go back together it was very difficult to get it all to press down tightly enough to tighten each set of screws. The project took about 2.5 hrs and I still don't think it is exactly right. I'm still going to have a professional out to finish the job. Also, the tool needed to complete the job was nothing fancy, but also not in everyone's home tool kit.

from inside the door remove torx screws down each side and top , pull panel back , removed 6 screws from back of dispenser ,unplug 1 wire connection ,reverse procedure , real easy repair.

First I watched the repair video provided at your site. Once I got the right part, it went like a breeze. Just a phillips head screw driver and 5 minutes of my time. Speaking if the right part.... I would suggest that you remove the 'LATCH-DOOR-NO Handle' from your parts list.It only cause confusion in ordering the part I needed, and a loss of several days time in the repair cycle.
All in all, a good repair experience. I would reccommend you to my " Do It Yourself" friends.
Thanks,
Harold L.

I remove the inner door panel, disconnected two quick release connectors, unscrewed the old part from the inner panel and installed the new one.

The new part arrived quickly and was the perfect match.

Turn off the DW power (pull the fuse or turn off the circuit breaker) Open the dishwasher door. Remove the torx screws around the periphery of the door inner panel. Lift up the inner panel far enough to get at the door latch. Lift out the entire door latch assembly. There are two wiring connectors attached to microswitches on the latch assemby. Remove the connectors. The connectors were pretty tight, so I needed pliers to pull the connectors off the switches. Discard the old latch. Get the new latch, and plug in the connectors (keep track of which wires go on which side). Lay the latch down in the door so it lines up with the mounting holes. Lay the cover back down, start each of the torx screws into their threaded holes, then tighten them all. Don't over tighten. Turn power back on. Job done. It almost takes as long to type it up as it does to make the repair.

I thought the door springs were broken so I ordered both springs and cables. After the parts arrived I removed the six screws that hold the dishwasher in place and slid the dishwasher out about five inches. Neither of the springs were broken but one of the cables was broken. I changed both cables, slid the dishwasher back in place and replaced the screws. The whole job took about 20 minutes. It was a very easy job.

Snapped the old part out and snapped the new part in.
It was a piece of cake.

I unscrewed the inner door panel and the old latch assembly came out. I went to the circuit breaker and cut off power to the DW. Then I unplugged the old latch assembly and plugged the new one in. There were some springy metal pieces that had to be pushed back to get the old plug off and the new one on. After that it was just a matter of aligning the holes of the latch assembly with the holes for the screws and replacing all the screw holding the door panel, and tightening them up.

I was extreemly pleased with the replacement handle unit. The original unit had a plastic pivot points - the replacement part replaced these points with metal rods. The pivot points on the old unit were the points of failure.

The repair should have been done with a "star" head. Not having this, I was able to use a hex wrench instead.

The repair time was less than 10 minutes, most of that time removing and replacing the star head screws. If you have removed the old part, you have essentially completed the repair.

The biggest problem was identifying the proper handle unit. There are two very similar. Measure the distance between the mount holes in the unit and refer to the grid in the picture. The grid on your site was extreemly helpfull given the lack of part numbers printed on the Maytag OEM parts.