Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This suspension spring is 7 inches in length, and is sold individually. It is a good idea to replace all six springs at once to maintain the same tension level. To complete this repair you will need a...
This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing machine. The pump is ac...
The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome ass...
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. If your machine is not draining properly or if it is noisy and s...
This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race was...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This is a replacement lid switch actuating cam for your washer. The cam is located on the underside of the washer lid, near the hinge. The cam actuates the lid switch, so your washer knows the lid is ...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
10 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
BARDELL
March 12, 2020
Does this washer have a balance ring?
For model number MAV7600AWW
Hello Bardell, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11738845 for the Snubber Ring. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the leg and the dome assembly. If during your spin cycle you notice your washer jumping and making loud whirring noises, you may need to replace your snubber ring. We hope this helps.
Hello Vickey, thank you for your question. If the leak is coming from the bottom of the tub we would recommend replacing PartSelect Number PS11741798 seal, and Hub and Seal Kit PartSelect Number: PS2349020. I hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Louis
January 25, 2023
Does this have self reset fuse or backer. It don't make any noise It shut off for about one hour. then it run like new.
For model number MAV7600AWW
Hello Louis, thank you for your question. The most common cause is a faulty Lid Switch PS11739463. We do not see a fuse for this model. We have a video for you to view on our site. We look forward to hearing from you.
I want to replace both fill hoses but can't reach the hose ends to unscrew old hoses and attach new hoses. What do I need to remove to access hose ends?
For model number MAV7600AWW
Hi Dan, thank you for reaching out. We have researched your model and attached a relevant video that might help you with your problem. We hope this is what you were looking for.
1 person found this helpful.
Was this helpful?
Thank you for voting!
James
November 29, 2019
How many cubic feet ?
For model number MAV7600AWW
Hello James and thanks for writing.
You might find that answer in our manual online. For more specialized assistance or to speak with someone about this, we would suggest calling the manufacturer of the unit directly. Once you get the information you need, we should be able to find the information on our site for you. Hope this helps
Lay washer on front, removed belt. Removed center pulley with thrust bearing (pulley was worn on upper end, against thrust bearing, thrust bearing was worn also). Installed new thrust bearing & pulley kit. Cleaned & lubed slots that motor insulators slide in, installed new belt.
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the
... Read morecomplete drum out of the waser and turn it upside down. You can see the plastic snubber ring that is worn, loosen the 6 screws just enough to get the old ring out and the new one in. WARNING (DO NOT TAKE THE SCREWS ALL THE WAY OUT OR THE BRAKE ASSEMBLY WILL RELEASE AND A SPECIAL TOOL IS NEEDED TO PUT IT BACK) Install the new ring, tighten the screws and put the tub back in connecting everything back up and use the 6 new springs. It really isn't that hard to do.
