MAV7600AWQ Maytag Washer - Instructions

shut off supply lines, remove cover on back of washer, remove drain hose from pump,inlet and exit. remove belt underneath washer from pump. remove 3 assembly screws. remove pump. set new pump in place. rescrew pump to washer. reatach inlet and exit hoses to pump put belt back on under washer put cover back on back of washer. turn supply flines back on. should work like new

The washer (bought 9 years ago) suddenly started squealing (metal on metal sound) during the spin cycle. After turning the washing machine off and unplugging it, the washer was tipped back and propped up on a milk crate to see the belt on the bottom. There was some rubber dust from the belt, so something had seized-up to some degree. The belt was removed and each pulley was tested to see if it made any noise. Upon spinning the pulley of the water pump a scraping sound was heard. Definitely not as loud as when the washer was on, but it probably would have been if it was spinning faster.

The washer was put upright again and the lid taped to the top to secure it before lifting the top. The top was opened by sliding a putty knife between the top and front panal near the left and right corners. There are two metal clasps that will release the top with gentle pressure, do not pry on the top. The top was lifted up and set back gently so as not to bend or break the hinges. There are two small screws on the upper inner right and left side of the front panel that were removed using a nut driver in order to remove the front panel.

With the front panel removed the water pump was visible in the front, lower left hand corner on the base. The two hoses were removed from the pump by moving the hose clamps up the hose, using pliers to loosen the clamps and then pulling off the hoses with a slight twisting back and forth. I put a few towels around the pump before removal to soak up the water that came out. The three bolts holding the pump in place were removed using a socket wrench and the pump removed.

The new pump was replaced, hoses were put back on, front panel replaced and the top relatch. The washer was tipped back again to get to the bottom to put on the new belt.

That was all. It worked great.

Notes:
1) Several people had mentioned having similar problems with the water pump and had observed a metal ring that had been pushed up where the pulley is connected to the shaft. I also observed this on the sqealing pump. The metal ring seem to work its way out and scrape on the metal mounting plate on the bottom of the pump. So if you see this ring, it is probably the pump.

2)I cleaned the pulleys since there was some rubber dust on them. Also you can remove the belt easily by pulling it slightly off the large pulley and then turning it off. When putting the belt back on, put it around the small pulleys first and then start it on the large pulley and turn it onto the large pulley. More leverage with the large pulley.

Unplugged Machine, Turned Off Water, Disconnected water and drain hoses. Let water run from hoses ino bucket.
Removed back plate where drain hose goes into back of machine. Used pliers to close the clamp holding to drain hose to remove it. I stuffed the exposed water pump opening with towels to keep water from spilling.
At this point I leaned the machine over on its front so the back of the machine was facing skyward. I placed a towel over the motor in case water spilled it would not get on the electrical components. I removed the belt on the bottom of the machine from the water pumps pully. I then removed the three screws mounting the pump to the bottom of the machine. I disconnected the other hose from the water pump that comes from the wash tank with the pliers. Once disconnected I stuffed the ends of both with towels to keep water from leaking out.
I took the new pump and connected the hose from the washer tub with pliers, mounted the pump back to the bottom of the tub with the three screws, replaced the belt, and reconnected the drain hose, and took the towel off the motor. I then replaced the back plate and set the machine upright. I connected all the hoses back up and plugged it in. It worked great. If you spill water on the motor you can dry it with a hair dryer.

1. Removed 3 phillips head screws and 2 hex head screws from upper back cover to expose the timer.
2. Removed the dial knob on front by popping off the cover with a screw driver then pryed up a smaller plastic button used to hold the knob in place.......knob slid off.
3. I then was able to tilt the whole panel forward to gain total access.to the wiring and timer
4. Disconnected wire harness from the switch.......had to pry up the snap tab that holds it in place.
5. Had to remove a small electrical board attached to the back of the timer......used screwdriver to pop it up and out (gently).
6. Removed one hold-down screw, lifted a little lock-tab and slid the unit to the left and lifted out and replaced.
7 . Reversed the above steps to install. This is not hard at all .>>.very easy to replace.
Machine works perfectly and I saved a couple hundred dollars for an appliance technician.
Thanks to the previous poster . I copied some of their comments and added some other comments..

The service and prompness from Parts Select was excellant and quick delivery.

Unplugged and removed the drain and supply hoses from the back; some water will run out so be ready for that. I laid the machine down on two 2x4s to keep from crushing the supply and drain nipples. Just follow the instructions included with the parts, all steps are straight forward accept for two things: 1. they talk about pulling down on the transmission shaft to slip on the retaining clip. With only the end of the shaft sticking out there isn't much to grab on to. I found by using a thin blade scraper inserted into the retaining clip groove, prying downward on the shaft I could then get a regular screwdriver blade into the same groove and expose the entire groove and slip on the clip. 2. they talk about "Adjusting Brake Disengagement" after studying this for a while it just refers to which thickness of thrust washer to use. After trying both the .062 and .032 I found that only the .032 would allow the retaining clip to engage. Rechecking the brake disengagement, everthing seemed to work fine. The machine now has a stronger spin cycle and even bath towels are ready for drying after the normal spin.

Turned off water suply. Removed drain (pipe is short). Then slid washer out so I could tilt it back and work under the washer. I put a wood brace under the front of the washer for safety. I then followed the instructions that came with the parts.

Removed the control panel, top and front panels to access the motor. Removed the motor and inspected. The motor looked fine. Leaned machine back and remove the brake cover following the directions posted by others on this website. Discovered grease and grime on the friction brake, which did not look right. The grease must have slung off of the transmission shaft. Wiped the brake clean with a dry rag and put machine back together. Machine did not run, motor only hummed. I replaced the motor only and the machine now works fine. My feeling is the grease caused the brake to stick and every time the motor started up, the sticking brake put a strain on the motor. Over time this cause the motor to burn up. Machine is only 6 years old. Sounds like a design flaw.

After examining the diagrams online, I removed the 3 screws holding on the back panel. Nothing seemed wrong so I tilted the machine to look underneath at the belt. All seemed OK but manually moving the belt by hand revealed that where the belt drives the pump had worn loose and was the source of the problem. Reading other descriptions of the ease of replacement of the pump, I ordered the new pump. It took approximately 15 minutes to remove the old pump and 10 minute to install the new pump and replace the belt. The machine is back to working fine. This is a fairly simple repair.

I first grasped the fabric softner dispenser and pulled it up and off agitator. I then removed the bolt from the center of the agitator with a 1/2" socket, 8" extension and ratchet. I grasped the agitator assembly and pulled it up and off. Reversed the procedure to install. The bolt can be started by placing a piece of paper towel over the socket, then inserting the bolt into the socket. It will hold it there while you start the bolt. I also took the opportunity to clean the accumulated soap scum from under the agitator while it was disassembled. An easy fix!!!

Removed the 2 screws on the front panel after unplugging the unit. Removed the 2 screws on the safety cover and removed the wiring coupling. Removed the 2 bolts that was holding down the belt adjuster. Fed adjuster around pully wheel after removing belt. Installed new motor and re-assembled in reverse of disassembly. Plugged in unit and tested motor. Unit still operating satisfactory. Wash about 5 loads everyday. Large family

Opened the front panel by using a flathead screwdriver (to pop the top lid up) and socket wrench (to loosen the front panel off). I then had to reach in and replace the missing/broken suspension spring. The spring was very difficult to extend so I used coins to lodge into the spring to elongate it. After the spring coils were loaded and held apart with coins (nickels and quarters) the spring could be installed using a pliers for leverage. The washer doesn't make the loud banging noise anymore!

Opened the top of the washing machine, removed the two screws and the front cover removed the agitater, drum and outer tub. replaced the bearing and seals and reassembled.

I used a putty knife to disengage the clips that attach the top of the washer to the front panel. The top will lay back without having to hold it however, I didn't trust it to stay up on it's own so I used a bungy cord and straped it onto a wire rack that hangs on the wall above my washer. Next I removed the two screws, one on each side, located on the inside of the front panel near the top of it. Then I gently pulled the front panel towards myself so that I could lift it off of the clips located at the bottom of the panel. The pump assembly is located at the front right corner inside of the washer. I disconnected the two hoses that run to the pump assembly and using my ratchet, I removed the 3 screws that hold the pump assembly in place. There is a belt on the bottom of the washer that goes around three pulleys, one of which is the pump assembly pulley. After I removed the pump assembly, I took the belt and laid it to the side. I then installed the new pump assembly. After I put everything back together, I gently tipped the washer over on it's side as far as I could and reinstalled the belt around all three pulleys. I started with the pulley on the left side and then the pulley in the middle and finally, the pump assembly pulley. I have washed a total of seven loads of laundry since I did the repair and have had no problems.

Move washer to area with plenty of room. I took mine out to the deck. take off front of cabinet remove back panel, remove old springs, (a bit hard) remove belt, lift out tub turn over and loosen screws do not remove!! remove old snubber and replace with new, Not bad. Put tub back in washer put on new springs(didn't think I'd ever get them on, not enough upperbody strength)Video would have been priceless!
reattach belt and panels put washer back in place. No noise upon spinning but I now have issues with the agitator, Need a new washer!

I checked out your other repair information and deided I could do this. Ordered the part and it as her several days before I expected it.

Ok, let's do this thing.

MAGIC TOOLS:
5/16" socket or wrench and #2 Phillips screwdriver and something to remove hose clamps - I recomend a 6" to 8" vice grips and a 6" to 8" plires.

1. Pulled the washer out in the middle of the floor and disconnected the hoses and removed the rear access cover, disconnected the pump hose, released the top using a 1/8' common screwdriver in that narrow space between the top and the front panel. Removed the 2 screws holding the front panel on and removed the front panel.

2. Disconnected fill level hose- toward the left rear side - turned the machine on it's side and walked the drive belt off, tipped it back up right and removed the 6 springs - be sure to note their orientation and location.

3. Lifted the whole assembly out of the top of the machine and set it upside down next to the machine.

4. Loosened the screws holding the snubber in place - NOTE I did not remove the screws - loosen them sequentially little by little untill you can get the snubber to come out. I did not remove the pulley as my Craftsman ratchet and standard - short - socket allowed me to get between the pulley and the screws to loosen them.

5. I removed the old well worn snubber, cleaned the area up and the new snubber actually fell into place and I retightened the screws in the reverse order until they were solid feeling.

6. I lifted the assembly back into the frame, reconnected the springs and the pump hose and the fill level hose. I reinstalled the front cover - AND HERE IS THE IMPORTANT PART!

7. You are so happy this is going so well that you forget to put the BELT back on before you hook up the hoses, so you have to unhook the hoses to put the belt back on and then rehook the hot and cold hoses and drain hose again.

8. Except for number 7 this is a piece of cake. My only concern is how often will I have to do this. The machine is only 8 years old.