MAV7600AGW Maytag Washer - Instructions

Pop the cap off the agitator/auger no tools needed. Once removed select a socket and a socket exstension. remove the screw amd pull off the part. Make sure to save the washer that may be still attached to the inside of the agitator. install the new agitator using the existing screw and washer. Takes about 15 minutes.

I pulled washer out and removed filler hoses from water supply and drain hose and tilted it forward placing three short 2X4's under the washer to keep it tilted forward. Removed
back plate with nutdriver. Removed belt from pulley and disconnected the two hoses from pump with pliers. Removed three large screws from pump base with nutdriver and removed old pump. Installed the new pump in reverse order. Quick and fairly easy took about 30 minutes.

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done

I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.

Screwed new part in, re-attached hoses and replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.

Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.

first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new

I watched video, couldn’t believe how easy to replace

After receiving the new part, I lifted the lid making sure it was level, then simply pushing the new pin in the lid hole, then pushing the whole thing back toward the corner of the lid until it clicked in.

I popped out the hinge pins, popped outthe busshings, popped out the cam. time less than 10 minutes, pressed in the limit cam, pressed in the bushings, pressed in the hinge pins. time about 5 minutes. the most important thing is my wife is extremely happy. I'm happy the parts fit perfectly.
also the parts arrived in 2 days.

I first changed the belt which helped but it still sounded like it was going to take off through the roof.....I did the pulley and bearing kit in hopes that it would do some good....it went really smoothly with no issues however it did not solve the problem....so it is working and I am going to just ride it out until it quits....thanks

Unhooked the macine pulled out for easy access .removed drive belt rear cover plate ,vaccumed remaining water out thru drain hose with wet and dry vac. Removed hose clamps and hoses .removed the three hex screws holding the pump to the base plate. The removed the old pump , Installed the new pump hoses access plate and belt . Hooked the machine up . Worked perfect.











the

I watched the video of the repair on this website and followed it. Was really easy & THANK GOD because this was my first repair. This has been a great machine and it looks like it will continue to be for a little while longer! Thanks for the video help and friendly navigation of your site!

Repaitmr was simple. Followed video instructions from web site. Problem I ordered wrong motor so it just blew my plugs fuse. Also needed pump. Changed motor to old motor installed new pump. Machine works great.

Followed the great instructions on your video

It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was stiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00

I watched the installation video. It was very helpful to see it done before doing the repair. I followed the video to take the old springs out and installed the new ones. Remember to check the snubbed ring and replace it too. The new springs and sunnier ring solved the banging and moving during the spin cycle. Now the washer is like new and the repair was less then $100. Thanks parts select, the help was greatly appreciated.