MAV6300AGW Maytag Washer - Instructions

took off front of washer , took off hose clamp removed old hose . replaced with new hose clamped back on put on front cover ran washer check for any leakes. done and done

first remove drive belt then then remove dust cover on bottom of shaft take 5/16 nut driver to only 4 of the screws off that hold the brake cover on install 4 5/16 screws 1" long in those 4 spots.reomve rest of screws then slowly reomve back out 1" screws to relve spring pressure from brake pad.install all new parts from partsselect.com then install other part taken off in oreder and make your wife very happy

I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.

Simple remove and replace. Plastic cam and hinges simply snap out, replacement parts snap right back in. Needle nose pliers were helpful to remove broken lid cam. With hinges and lid removed, took advantage of great opportunity to clean lid and and top of washer.

The replacement was very easy, just one bolt and RR was a snap. However, the first part that came was defective and I called the 800 number, spoke to the rep and the part came the next day. Excellent customer service, and would do business again

I first took the fabric softener dispenser off and used
a ratchet wrench to take the nut off. I then removed
the agitator, put the new one on and reversed the process. It was extremely easy!

Removed inspection panel on rear of washer. Pump right there. Removed inlet and outlet hoses with pliers on squeeze clamps. Three 3/8" size self tapping screws were removed and old pump came right out. Reversed process with new pump from this site that fit perfectly. New pump was an upgrade factory part that mounted inside washer without a mounting plate as the old one did.

I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.

Replace the motor in 25 minutes, my repair guy said it was not worth the time , I got this motor for less than $150. And save my self over $600.00, this was incredible.

Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.

Use a blade to pop off the fabric softener dispenser cup. Use socket and extension to unscrew the single hex bolt that attaches the assembly to the shaft. Lift off the assembly and recover the flat washer. Install the new assembly over the shaft and install the original hex bolt and washer. Tighten firmly. Snap the dispenser cup back in place.

I went ot the Parts Select web site, and read what other people had done with the same problem. The advice was right on. Using the paper towel to hold the screw in place during reassembly ws great advice. Thanks for the heads- up.

Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.

take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose

Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.