MAT12CSAAW Maytag Washer - Instructions

Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck

I removed three small bolts on the back of top panel unpluged electric plug on lid switch popped out old switch popped in new plugged in switch put top back on with the three small bolts. The wife was back in business. Easy as 1 2 3

First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixed to your machine where you can lift the lid and it will stay up without falling.

Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.

This is a coin-op washer so the timer had to be removed through the coin box. The top lid was first removed from the coin box. There is one 5/16 hex head screw holding the timer in. After removing the screw the timer was lifted from the box. It is a tight fit that requires some wiggling around of the timer. There are two plug in wire harnesses attached to the timer. Because of the position of the timer the wires are a little short, but are able to be unplugged. The new timer was installed and the procedure reversed.

Followed the procedures recommended for replacement of all the parts included in the Tub Bearing Kit and the Mounting Stem/Tub Seal kit as illustrated in a detailed, 32 minute repair video for the Maytag A606 washer which is available on YouTube. Many difficulties were experienced in the disassembly procedures due to extensive corrosion of tub bearing and tub stem parts (the washer is 47 years old).
I was not successful in using a special tub wrench that was purchased to break loose the old tub mounting stem and its threaded lock nut. The old tub mounting stem, lock nut, and the tub bearing race had to be cut off the threaded support shaft using a saws-all electric tool. Finally, corrosion on the edge of the tub caused problems with water leaks once the tub top and its rubber tub seal ring were reinstalled and the washer was put back into operation. The bottom line is that it may be questionable to attempt major repairs on washers that are 40+ years old and have any extensive corrosion in internal, mechanical parts.

It was as simple as leaning the machine back far enough so I could get to the belts - which were on the bottom. The diagrams that came with the ordered parts were right on. This is the first time I have attempted this myself - my repairman has retired - I'm sure I will do it again.

Took off the top rear off the washer, Removed the top control section,disconnected the wire harness, snaped out the old switch and installed the new one, connected the wire harness, put everything back together, and it was working again!

Removed the front panel. Then blocked up the front of the machine. Removed the pump belt. Removed the 3 5/16" screws from the bottom of the old one and tilted it slightly to remove. Put the new one in and reinstalled the 3 screws. Put the belt back on and slid new pump all the way to the right and tightened 1 screw. Loosened the screw until there was about 1/4" of gap when squeezed the belt together. Tightened the one screw, then the other 2. Put the front panel back on and lowered the machine. New pump works great.

Disconnected power. Then I removed the cover to the console on the back to gain access to the lid switch. Removed the switch assembly by hand and disconnected from electrical plug on machine. Attached new assembly unit to plug and reinserted new assembly onto machine. Reattached cover to console.

Switch material hardened due to old age & broke easily when force fitted. Ordered parts online & in two business day it arrived.

First open the lid & removed the side latch with screw driver carefully. Checked the length of the new plunger with the old one with respect to length & compare the stroke. Slide fit the switch & rectified the play in the plunger pusher with super glue.

iremove the two screws that is on the lid and then ipulled that out then secound step remove the part is on the back were is the suit of the washer machine were is the hoses of the water hot and cold its berry easy to do it your self thank you

Removed the damaged legs, replaced with parts from this site and leveled the washer .

After turning the water off and unplugging the machine, I took the front panel off the washing machine. I then slipped the belt off the pump sprocket. The pump was right in the front and easy to remove. All I needed was a screwdriver, for the hose clamps, and a 5/16" socket to remove the old pump. I then installed the new pump, with the existing screws, re-attached the 2 hoses, slipped the belt back on, and popped the front panel back into place. The new pump works great and the leak is gone. The whole job onlt took about 30 minutes.

The hardest part was actually finding the right part. It was easy to take of the control panel. make sure you unplug and plug in the correct wires....

I thought that would be it, but after doing that you need to fine adjust the whole assembly so that the timers and automatic switches work well.

That's about it.

Took a look at the new door switch assembly, used a socket wrench to remove the old, took wires off of old and attached them to the corresponding terminal on the new. attached the new assembly inside the top panel. Works!