Switch to Classic
Models > MAH6500AWW

MAH6500AWW Maytag Washer - Overview

Sections of the MAH6500AWW

[Viewing 12 of 12]

Manuals & Care Guides for MAH6500AWW

Click to download
Keep searches simple, eg. "belt" or "pump".
Light Bulb - 10W – Part Number: WP22002263
Light Bulb - 10W
★★★★★
★★★★★
(16)
PartSelect #: PS11739347
Manufacturer #: WP22002263
This ten watt appliance light bulb is two inches tall. It is used with both washers and dryers.
$16.94
  In Stock
Screw – Part Number: WP400021-1
Screw
★★★★★
★★★★★
(1)
PartSelect #: PS11742240
Manufacturer #: WP400021-1
Sold individually.
$12.25
  In Stock
Bellow – Part Number: 12002533
Bellow
PartSelect #: PS2003890
Manufacturer #: 12002533
Also known as the door boot seal. This part includes the drain and plug. The seal is located around the door of the washer to prevent water from leaking.   No Longer Available
Screw, 8/18 x 3/8 – Part Number: WP90767
Screw, 8/18 x 3/8
★★★★★
★★★★★
(2)
PartSelect #: PS11746840
Manufacturer #: WP90767
This screw is sold individually.
$7.54
  In Stock
Hose Clamp – Part Number: WP596669
Hose Clamp
★★★★★
★★★★★
(1)
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$7.54
  In Stock
Foot, Front - Single – Part Number: WPW10001130
Foot, Front - Single
★★★★★
★★★★★
(1)
PartSelect #: PS11747965
Manufacturer #: WPW10001130
The front facing foot is sold individually. It is used on your washing machine and can also be known as an adjustable leveling leg. This specific front facing leveling leg has a rubber foot. It is imp...
$7.32
  In Stock
Rubber Foot Pad – Part Number: WP210684
Rubber Foot Pad
★★★★★
★★★★★
(1)
PartSelect #: PS11738859
Manufacturer #: WP210684
The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place. This foot pad is ju...
$12.68
  In Stock
Lip Seal Kit – Part Number: 12002022
Lip Seal Kit
★★★★★
★★★★★
(2)
PartSelect #: PS2003500
Manufacturer #: 12002022
This kit comes with grease, earlier lip seal, revised lip seal, o-ring, seal tool, and washer kit. Used primarily on front load washers. NOTE: Bearing is NOT sold separately. It is only available ...
$99.47
  On Order
Drive Belt and Motor Isolator Kit – Part Number: 12001788
Drive Belt and Motor Isolator Kit
★★★★★
★★★★★
(8)
PartSelect #: PS2003327
Manufacturer #: 12001788
This kit contains a flat drive belt, two motor isolators, and an instructions sheet. The drive belt is made to slip on the pulley until the basket gets up the desired speed.
$40.85
  In Stock
Inner Door - white – Part Number: WP22003275
Inner Door - white
★★★★★
★★★★★
(8)
PartSelect #: PS11739424
Manufacturer #: WP22003275
This inner door assembly is twenty-two inches long. It is all white in color and is made of plastic.
$92.35
  In Stock

Questions And Answers for MAH6500AWW

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

5 questions answered by our experts.
    Sort by:
    Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
    Kathy Merriman
    February 4, 2020
    What is the cubic foot capacity of this washer?
    For model number MAH6500AWW
    Hello Kathy, thank you for your question. The capacity of this unit is Capacity: 3.34 Cu. Ft.. I hope this helps.

    4 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Art
    August 20, 2021
    Instructions as to what panels to remove to replace water drain pump assembly (bottom, rear?)
    For model number MAH6500AWW
    Hello Art, Thank you for your inquiry. You would remove the rear panel in order to access the drain pump in order to replace it. We have included a link to our repair video on repairing the drain pump in order to assist you. Good luck with your repair.
    play video

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Joe
    January 18, 2020
    I had to replace my bearings and seal. I got it all back together but the issue is that it seems that the drum is tight and really hard to spin. I don't know why it is so hard to spin and tight.
    For model number MAH6500AWW
    Hello and thank you for writing. It is possible that an obstruction has jammed the drum and makes it hard to spin, you should check it for debris that might have gotten in there during the repair. We hope this helps. Please contact us anytime if you require further assistance.

    2 people found this helpful.

    Was this helpful?
    Thank you for voting!
    Alice
    October 14, 2021
    Are the parts interchangeable between models mah6500aww and mah6500awq?Which model is more recently manufactured? I am considering replacing the aww with the awq due to a loud grinding noise on the spin cycle.
    For model number MAH6500AWW
    Hello Alice, Thank you for the question. The AWW indicates this is a White appliance and the AWQ is a Bisque color appliance. Parts would be the same internally, just the outside color is different. We hope this helps!

    Was this helpful?
    Thank you for voting!
    Carlos
    June 16, 2021
    I am told that there is oil on the floor, could it be from the transfer case? I could not find a cut sheet. Thank you. Carlos.
    For model number MAH6500AWW
    Hello Carlos, Thank you for the question. Normally this is an indication the Lip Seal Kit is worn or damaged and will need to be replaced. We hope this helps!

    Was this helpful?
    Thank you for voting!
    Related Parts:

      Common Symptoms of the MAH6500AWW

      [Viewing 15 of 15]
      Leaking
      Fixed by
      these parts
      Show All
      Noisy
      Fixed by
      these parts
      Show All
      Will not drain
      Fixed by
      these parts
      Show All
      Shakes and moves
      Fixed by
      these parts
      Show All
      Will not stop filling with water
      Fixed by
      these parts
      Show All
      Pumps but will not spin
      Fixed by
      these parts
      Show All
      Burning smell
      Fixed by
      these parts
      Show All
      Lid or door won’t close
      Fixed by
      these parts
      Show All
      Will Not Start
      Fixed by
      these parts
      Show All
      Will not agitate
      Fixed by
      these parts
      Show All
      Marks left on clothes
      Fixed by
      these parts
      Show All
      Spins slowly
      Fixed by
      these parts
      Show All
      Lid or door will not open
      Fixed by
      these parts
      Show All
      Will not fill with water
      Fixed by
      these parts
      Show All
      No hot or cold water
      Fixed by
      these parts
      Show All
      Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
      Spinner making loud whining noise.
      As Typical with this Neptune front load washer, the Water Seal fails to keep water from getting into the bearings. The bearings start to sound like a jet engine at high speed spins once the grease is washed out (nice grease splatter at the back of the cabinet). You can replace the Lip Seal but the bearings are not part of the kit. It is a waste of time to replace the seal kit if the bearings are already bad or going bad. You can't buy the bearings from here or any other appliance part store. You have to purchase a new tub in order to get new bearings, at $500+. Not worth it. I purchased the Lip Seal Kit with the intention of removing the bearings and replacing. The instructions that come with the kit explain with diagrams how to disassemble. In order to remove the spinner from the outer tub, I had to remove the whole tub, place it face down on some 2x4's and hit the spinner shaft with a hammer and block of wood to get it out of the old bearings. It came out fairly quickly. I removed the old lip seal (you can use the two access holes at the back of the outer tub to bang out the lip seal with a nail) and using a hammer and screwdriver, banged out the front bearing in the outer tub from the back and through the back bearing. This took a little while of moving around the bearing edge and tapping out, especially since there is a pipe spacer between the 2 bearings. It can be moved partly out of the way. The spacer will fall out with the front bearing. I then removed the C-clip that holds in the back bearing and banged out using the same method as the front bearing but from the inside. It too took a lot of tapping around the edges due to lots of corrosion. Once I had the bearings out, I looked up the make and model printed on the covers. Order using a DDU designation which is a rubber seal on both sides, like originals. I cleaned up the bearing mounting surfaces using a dremel tool and wire brush attachment. Make sure you get the metal free of any contamination. Use grit paper if necessary. I also sanded down the spinner shaft and got the spindle nice and shiny. I inserted the larger front bearing first (use a little grease on outside edge), it was a very tight fit and had to tap in using a hammer and metal rod. Make sure it is all the way in. Install the new seal kit (mine was the crummy original design, not the revised one). With the spinner tub on the floor shaft up on some 2x4's (light coating of grease on shaft), place the outer tub over the spinner with the shaft inserting through the new bearing and out the back. The shaft isn't an interference fit with the front bearing so it should slide in easily. WIth the shaft fully inserted, install the pipe spacer (cleaned up) then place the back bearing (outside edge greased) over the shaft and into the outer tub. This is an interference fit and will have to be tapped into place. It also was a tight fit into the tub. WIth it part of the way into the tub, I installed the belt pulley and tightened it down using a longer bolt than supplied, and this pushed the bearing the rest of the way in. I then installed the the C-ring. Not sure why the C-ring is needed with the bearing being such a tight fit. I installed the tub assembly back into the washing machine cabinet and installed the pulley and belt.. After reassembling the complete washer (after much cleaning of dust and soap scum, etc) I ran the unit once with no clothes to make sure any contaminates (grease, etc) where washed out first. So far so good, nice and quiet. If it last me another 5-10 years I will be happy. It will fail again for the same reason since I had to use the same lame seal kit and didn't have the revised version un
      Parts Used:
      Lip Seal Kit
      • Richard from Greenville, NH
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        More than 2 hours
      • Tools:
        Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
      312 of 332 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Bad bearings on inner drum
      Unplug and turn off water.....Removed belt drive cover. Rolled belt off of pulley. Removed pulley from back of splined shaft. Removed front door and front panel. Removed two screws that hold top of washer down, 4 screws that hold detergent/bleach tray to top and tilted top back. Removed 4 screws that hold door seal assembly to frame. Popped clips from back of seal away from outer drum. Note locations to reinstall. Pulled small hose away from seal assembly (located at bottom of door seal. Removed door seal assembly. Removed torx screws from tumblers in inner drum to access nylock nuts that hold inner drum to spinner. Removed inner drum. Pulled spinner shaft from outter drum. Removed seal from inside outer drum where shaft passes through bearings. Knocked outside bearing out with drift from inside outer drum. Be careful no to nick/scratch bearing fit or shoulder. Go to the back of the machine and knock the inner bearing out using same method. TAKE YOUR TIME. Outer drum 600 bucks, so don't mess it up. Bearings are available at local bearing shop. NSK 6206DU and NSK 6207DU. Cleaned well and made sure that bearing fits were in good shape. Cleaned up spacer that fits between bearings. Note the way it comes out of the bearing holder (it is tapered on one end). Tapped outer race of inside and outside bearings into fits (barely) after lying the spacer between the bearings in the bearing sleeve. Used threaded rod and some washers of the proper size to pull bearings together. Tapped outer races to make sure that they were seated. Check spacer sleeve fit between inner races (hold it up in the proper location with your fingers....should be snug. Pressed new seal in per directions. Trial fit spinner into bearings/spacer. Installed pulley and belt. Note how bearing spacer and shoulders and pulley clamp inner races together so that you don't get any slip/slop/slap. Reassembled in reverse. Only problem I had was with the door latch manual releast that I accidently clamped between the bleach/detergent dispenser and lid when closing it up....had to adjust. Drank beer and bragged to wife. Been about 20 loads no....no leaks and as quiet as it was new. Took about 2 hours to take it apart and about 3 to put back together....Not a bad job. Definitely cheaper than an outer drum assembly.
      Parts Used:
      Lip Seal Kit
      • Michael from Cache, OK
      • Difficulty Level:
        A Bit Difficult
      • Total Repair Time:
        More than 2 hours
      • Tools:
        Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
      149 of 151 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!
      Leak from Door boot
      My washer was leaking when i opened the front panel to check i found that the water was leaking from door boot which had gashes in it. the task was real easy. and took me 30 minutes to fix it, this was my first time repairing any appliance and i found real easy to do. here are the steps i took:
      1. unscrew 2 door screws and the 2 screws opposite to them on the other side (on right if you are facing the washer)
      2. take door out by lifting it slightly and then pulling it out.
      3. hold front panel from both sides and then push in and twist outward this willl diengage front panel from the hooks on side.
      4. tilt front panel towards you about 40 deg. adn pull it up.
      5. to take top out, first remove all 4 screws from soap dispenser and take the dispenser out (just pull up after unscrewing)
      6. unscrew the electrical unit (where bulb is) in front top by taking out the 2 nuts Note: you must take out left most socket/coupler by pulling it before unscrewing the left nut that will give space for your wrench.
      7. In the front corner the Top is bolted to side frame bars you will have to look under top corner and you will see 1 nut on each side, unscrew those nuts and the lift the top ( if you have enough space (about a foot) behind the washer the Top ca n actually go all the way back and rest on wall.)
      8. from top view you will see a spring and metal wire system holding your boot, notice the spring position, spring has 2 hooks on each side, with needle nose pliers pull on the spring hook and have someone else disengage wire from spring hook. ( when it is time to put the wire back on the new boot just follow the same thing)
      9. once wire is out take the boot out by pulling it from all directions. note: you may still have water in the washer system so before you take the boot out be ready with a bucket to catch it write under the boot plug.
      10. your boot is still connected to washer withe the plug at the bottom. with help from needle plier press on clamp and pull plug out. note: if you see water flowing out from drain pipe (where the boot plug goes in try to keep it up to lwer the level of water that will stop the water flowing out (i took help from my 6 year old daughter for this job) now your old boot is out, trash it.:)
      11. put the new boot the lip of drum and put the wire back on (again i enlisted my wife and my daughter to keep the wire in place, you cannot do it alone. with 3 of us putting wire was a breeze. put the spring back at the exact same place and with exact orientation.
      Note: when you start to put wire and new boot on washer drum lip make sure the tiny cuts/slots on the boot slip into the the notches on washer lip other you will have leak from these spaces.
      12.now rest is all easy. attach the drain plug back on and then push the tabs of boot into the frontto secure it.
      13. put all the thing that you took out in the same order all the way to door and you are ready to go
      NOTE: i did not front panel back on for couple of days to make sure there i no other leak and also to make sue that boot is not leaking.

      have fun
      Parts Used:
      Bellow
      • Sirish from Thorndale, PA
      • Difficulty Level:
        Easy
      • Total Repair Time:
        15 - 30 mins
      • Tools:
        Nutdriver, Pliers, Screw drivers
      141 of 147 people found this instruction helpful.
      Was this instruction helpful to you?
      Thank you for voting!