Parts That Fix Maytag Washer MAH6500AWW Leaking
Leaking is a commonly reported symptom for the MAH6500AWW Maytag Washer, and we have put together a full guide on how to fix this. This advice is based on feedback from people who own this exact appliance. We have listed the most common parts for your MAH6500AWW Maytag Washer that will fix Leaking. We have included repair instructions, and helpful step-by-step video tutorials. If you are experiencing this issue, not to worry, DIYers just like you have fixed this, and shared their experience to help you!
1 Bellow
Fixes Symptom 39% of time
Also known as the door boot seal. This part includes the drain and plug. The seal is located around the door of the washer to prevent water from leaking.
No Longer Available
PartSelect Number PS2003890
Manufacturer Part Number 12002533
Replacing your Maytag Washer Bellow
Customer Repair Stories
mold on door gasket
Apparently the only way to solve the notorious mold problem on the rubber gasket of the Maytag Neptune front-loading washer is by replacing the door gasket. I ordered the boot kit from you and my husband attempted to do the job without the benefit of an instruction sheet, but I was finally forced to download the repair manual from the Ma
... Read more
ytag website. Using a screwdriver to remove the the front door, the detergent dispenser, and the shroud, he was able to remove the old gasket, though stretching the spring that held the gasket in place required some strength. The only tricky part was stretching the spring again that holds the replacement gasket in place. With a little ingenuity, a screwdriver (and some dishwashing liquid to make the task a little easier) he finally accomplished it. It took him over 3 hours, but the job is done and the washer seems to be working fine. Your service was fast and efficient and I wouldn't hesitate using your service again, but enclosing a detailed instruction sheet would have been helpful. Now that he knows how to do the job he acknowledges that the it shouldn't take him more than an hour the next time, should the gasket need replacement again. Meanwhile I am going to try tackling the mold problem by leaving the front door open after wiping out the water that remains on the door gasket after each wash.
Read less
-
Roberta from Ocean Isle Beach, NC
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Screw drivers, Socket set
57 of 63 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leak from Door boot
My washer was leaking when i opened the front panel to check i found that the water was leaking from door boot which had gashes in it. the task was real easy. and took me 30 minutes to fix it, this was my first time repairing any appliance and i found real easy to do. here are the steps i took:
1. unscrew 2 door screws and the 2 sc ... Read more rews opposite to them on the other side (on right if you are facing the washer)
2. take door out by lifting it slightly and then pulling it out.
3. hold front panel from both sides and then push in and twist outward this willl diengage front panel from the hooks on side.
4. tilt front panel towards you about 40 deg. adn pull it up.
5. to take top out, first remove all 4 screws from soap dispenser and take the dispenser out (just pull up after unscrewing)
6. unscrew the electrical unit (where bulb is) in front top by taking out the 2 nuts Note: you must take out left most socket/coupler by pulling it before unscrewing the left nut that will give space for your wrench.
7. In the front corner the Top is bolted to side frame bars you will have to look under top corner and you will see 1 nut on each side, unscrew those nuts and the lift the top ( if you have enough space (about a foot) behind the washer the Top ca n actually go all the way back and rest on wall.)
8. from top view you will see a spring and metal wire system holding your boot, notice the spring position, spring has 2 hooks on each side, with needle nose pliers pull on the spring hook and have someone else disengage wire from spring hook. ( when it is time to put the wire back on the new boot just follow the same thing)
9. once wire is out take the boot out by pulling it from all directions. note: you may still have water in the washer system so before you take the boot out be ready with a bucket to catch it write under the boot plug.
10. your boot is still connected to washer withe the plug at the bottom. with help from needle plier press on clamp and pull plug out. note: if you see water flowing out from drain pipe (where the boot plug goes in try to keep it up to lwer the level of water that will stop the water flowing out (i took help from my 6 year old daughter for this job) now your old boot is out, trash it.:)
11. put the new boot the lip of drum and put the wire back on (again i enlisted my wife and my daughter to keep the wire in place, you cannot do it alone. with 3 of us putting wire was a breeze. put the spring back at the exact same place and with exact orientation.
Note: when you start to put wire and new boot on washer drum lip make sure the tiny cuts/slots on the boot slip into the the notches on washer lip other you will have leak from these spaces.
12.now rest is all easy. attach the drain plug back on and then push the tabs of boot into the frontto secure it.
13. put all the thing that you took out in the same order all the way to door and you are ready to go
NOTE: i did not front panel back on for couple of days to make sure there i no other leak and also to make sue that boot is not leaking.
have fun
1. unscrew 2 door screws and the 2 sc ... Read more rews opposite to them on the other side (on right if you are facing the washer)
2. take door out by lifting it slightly and then pulling it out.
3. hold front panel from both sides and then push in and twist outward this willl diengage front panel from the hooks on side.
4. tilt front panel towards you about 40 deg. adn pull it up.
5. to take top out, first remove all 4 screws from soap dispenser and take the dispenser out (just pull up after unscrewing)
6. unscrew the electrical unit (where bulb is) in front top by taking out the 2 nuts Note: you must take out left most socket/coupler by pulling it before unscrewing the left nut that will give space for your wrench.
7. In the front corner the Top is bolted to side frame bars you will have to look under top corner and you will see 1 nut on each side, unscrew those nuts and the lift the top ( if you have enough space (about a foot) behind the washer the Top ca n actually go all the way back and rest on wall.)
8. from top view you will see a spring and metal wire system holding your boot, notice the spring position, spring has 2 hooks on each side, with needle nose pliers pull on the spring hook and have someone else disengage wire from spring hook. ( when it is time to put the wire back on the new boot just follow the same thing)
9. once wire is out take the boot out by pulling it from all directions. note: you may still have water in the washer system so before you take the boot out be ready with a bucket to catch it write under the boot plug.
10. your boot is still connected to washer withe the plug at the bottom. with help from needle plier press on clamp and pull plug out. note: if you see water flowing out from drain pipe (where the boot plug goes in try to keep it up to lwer the level of water that will stop the water flowing out (i took help from my 6 year old daughter for this job) now your old boot is out, trash it.:)
11. put the new boot the lip of drum and put the wire back on (again i enlisted my wife and my daughter to keep the wire in place, you cannot do it alone. with 3 of us putting wire was a breeze. put the spring back at the exact same place and with exact orientation.
Note: when you start to put wire and new boot on washer drum lip make sure the tiny cuts/slots on the boot slip into the the notches on washer lip other you will have leak from these spaces.
12.now rest is all easy. attach the drain plug back on and then push the tabs of boot into the frontto secure it.
13. put all the thing that you took out in the same order all the way to door and you are ready to go
NOTE: i did not front panel back on for couple of days to make sure there i no other leak and also to make sue that boot is not leaking.
have fun
Read less
-
Sirish from Thorndale, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
143 of 150 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 19% of time
This inner door assembly is twenty-two inches long. It is all white in color and is made of plastic.
$
101.32
In Stock
PartSelect Number PS11739424
Manufacturer Part Number WP22003275
Replacing your Maytag Washer Inner Door - white
Customer Repair Stories
Water leaking down the front of the washer
The inner door panel was damaged by something getting caught in between it and the tub wearing a hole in the plastic.
Remove door hinges.
Remove screws on sides(2 on each hinge)and 4 on otherside and 2 on bottom.
Pull inner door panel (plastic) out.
Remove doorlatch by flipping up center tab and squeezing sides toget ... Read more her.
Remove metal tabs by tilting up the backside and tilting down the front (screw hole side) and pulling through the back.
Reverse for reassembly - relatively easy.
Remove door hinges.
Remove screws on sides(2 on each hinge)and 4 on otherside and 2 on bottom.
Pull inner door panel (plastic) out.
Remove doorlatch by flipping up center tab and squeezing sides toget ... Read more her.
Remove metal tabs by tilting up the backside and tilting down the front (screw hole side) and pulling through the back.
Reverse for reassembly - relatively easy.
Read less
-
David from Gibsonia, PA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
15 of 17 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
inner door was dammaged when i washed my sons football- ribpads.
i removed the door,placed it on the kitchen tabel and removed 8 screws that hold the innerpart to the outer part and exchanged parts . there was a spring and a vent piece that snap on and off too. then i reinstalled the door and ran a load to check for leaks and there were none it was very easy but the best part of the repair was that i o
... Read more
rdered the part on saturday nite and recieved it on monday , part select .com i thank you for your excellent service.......
Read less
-
enrique from crest hill, IL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
22 of 24 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 12% of time
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.
$
7.76
In Stock
PartSelect Number PS11743008
Manufacturer Part Number WP596669
Replacing your Kenmore Washer Hose Clamp
Fixes Symptom 8% of time
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.
$
11.10
In Stock
PartSelect Number PS11740613
Manufacturer Part Number WP285655
Replacing your Kenmore Washer Hose Clamp
Fixes Symptom 4% of time
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$
135.45
In Stock
PartSelect Number PS11739466
Manufacturer Part Number WP22003834
Replacing your Maytag Washer Water Inlet Valve with Thermistor
Customer Repair Stories
The washer was stating NF code in the panel. It was not refilling for the rinse cycle. I had to manually press the button.
Turn the washer to the back. Unscrew the upper right corner water inlet valve. Take it out then replace it with new valve. Then turn your washer on and it will work just like brand new !!!!
-
Azeem from Clermont, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
14 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water would intermittently stop flowing into machine
Unplugged power cord, turned off water and disconnected cold and hot water lines. Removed two screws on bracket at water inlet area on back of washer. removed loose bracket and removed one screw that held water control valve (hot and cold). Unplugged four clipon electrical connections (marked before removal for ease of reconnection)
... Read more
Used flat tip screwdriver to remove hose clip from hose that went from valve into machine. Connected four clip on electrical connections and reconnected intake washer hose to water valve. I put a tiny bit of plumbers grease on plastic valve nipple to make it easier to push nipple into rubber hose. Reattached one screw to anchor valve to metal bracket. Repositioned bracket and attached two screws that anchored it to the washer. Reconnected hot and cold water lines and turned on hot and cold water to check for leaks. Plugged in power cord and started a wash cycle to once again check for leaks before pushing machine back into place. Wife didn't think I was "talented" enough to fix the washer, but I proved her wrong.
Read less
-
Nicholas from Duarte, CA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
53 of 62 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 3% of time
This kit comes with grease, earlier lip seal, revised lip seal, o-ring, seal tool, and washer kit. Used primarily on front load washers. NOTE: Bearing is NOT sold separately. It is only available with the outer tub assembly.
$
143.93
In Stock
PartSelect Number PS2003500
Manufacturer Part Number 12002022
Replacing your Maytag Washer Lip Seal Kit
Customer Repair Stories
Bad bearings on inner drum
Unplug and turn off water.....Removed belt drive cover. Rolled belt off of pulley. Removed pulley from back of splined shaft. Removed front door and front panel. Removed two screws that hold top of washer down, 4 screws that hold detergent/bleach tray to top and tilted top back. Removed 4 screws that hold door seal assembly to frame
... Read more
. Popped clips from back of seal away from outer drum. Note locations to reinstall. Pulled small hose away from seal assembly (located at bottom of door seal. Removed door seal assembly. Removed torx screws from tumblers in inner drum to access nylock nuts that hold inner drum to spinner. Removed inner drum. Pulled spinner shaft from outter drum. Removed seal from inside outer drum where shaft passes through bearings. Knocked outside bearing out with drift from inside outer drum. Be careful no to nick/scratch bearing fit or shoulder. Go to the back of the machine and knock the inner bearing out using same method. TAKE YOUR TIME. Outer drum 600 bucks, so don't mess it up. Bearings are available at local bearing shop. NSK 6206DU and NSK 6207DU. Cleaned well and made sure that bearing fits were in good shape. Cleaned up spacer that fits between bearings. Note the way it comes out of the bearing holder (it is tapered on one end). Tapped outer race of inside and outside bearings into fits (barely) after lying the spacer between the bearings in the bearing sleeve. Used threaded rod and some washers of the proper size to pull bearings together. Tapped outer races to make sure that they were seated. Check spacer sleeve fit between inner races (hold it up in the proper location with your fingers....should be snug. Pressed new seal in per directions. Trial fit spinner into bearings/spacer. Installed pulley and belt. Note how bearing spacer and shoulders and pulley clamp inner races together so that you don't get any slip/slop/slap. Reassembled in reverse. Only problem I had was with the door latch manual releast that I accidently clamped between the bleach/detergent dispenser and lid when closing it up....had to adjust. Drank beer and bragged to wife. Been about 20 loads no....no leaks and as quiet as it was new. Took about 2 hours to take it apart and about 3 to put back together....Not a bad job. Definitely cheaper than an outer drum assembly.
Read less
-
Michael from Cache, OK
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
159 of 162 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Spinner making loud whining noise.
As Typical with this Neptune front load washer, the Water Seal fails to keep water from getting into the bearings. The bearings start to sound like a jet engine at high speed spins once the grease is washed out (nice grease splatter at the back of the cabinet). You can replace the Lip Seal but the bearings are not part of the kit. It i
... Read more
s a waste of time to replace the seal kit if the bearings are already bad or going bad. You can't buy the bearings from here or any other appliance part store. You have to purchase a new tub in order to get new bearings, at $500+. Not worth it. I purchased the Lip Seal Kit with the intention of removing the bearings and replacing. The instructions that come with the kit explain with diagrams how to disassemble. In order to remove the spinner from the outer tub, I had to remove the whole tub, place it face down on some 2x4's and hit the spinner shaft with a hammer and block of wood to get it out of the old bearings. It came out fairly quickly. I removed the old lip seal (you can use the two access holes at the back of the outer tub to bang out the lip seal with a nail) and using a hammer and screwdriver, banged out the front bearing in the outer tub from the back and through the back bearing. This took a little while of moving around the bearing edge and tapping out, especially since there is a pipe spacer between the 2 bearings. It can be moved partly out of the way. The spacer will fall out with the front bearing. I then removed the C-clip that holds in the back bearing and banged out using the same method as the front bearing but from the inside. It too took a lot of tapping around the edges due to lots of corrosion. Once I had the bearings out, I looked up the make and model printed on the covers. Order using a DDU designation which is a rubber seal on both sides, like originals. I cleaned up the bearing mounting surfaces using a dremel tool and wire brush attachment. Make sure you get the metal free of any contamination. Use grit paper if necessary. I also sanded down the spinner shaft and got the spindle nice and shiny. I inserted the larger front bearing first (use a little grease on outside edge), it was a very tight fit and had to tap in using a hammer and metal rod. Make sure it is all the way in. Install the new seal kit (mine was the crummy original design, not the revised one). With the spinner tub on the floor shaft up on some 2x4's (light coating of grease on shaft), place the outer tub over the spinner with the shaft inserting through the new bearing and out the back. The shaft isn't an interference fit with the front bearing so it should slide in easily. WIth the shaft fully inserted, install the pipe spacer (cleaned up) then place the back bearing (outside edge greased) over the shaft and into the outer tub. This is an interference fit and will have to be tapped into place. It also was a tight fit into the tub. WIth it part of the way into the tub, I installed the belt pulley and tightened it down using a longer bolt than supplied, and this pushed the bearing the rest of the way in. I then installed the the C-ring. Not sure why the C-ring is needed with the bearing being such a tight fit. I installed the tub assembly back into the washing machine cabinet and installed the pulley and belt.. After reassembling the complete washer (after much cleaning of dust and soap scum, etc) I ran the unit once with no clothes to make sure any contaminates (grease, etc) where washed out first. So far so good, nice and quiet. If it last me another 5-10 years I will be happy. It will fail again for the same reason since I had to use the same lame seal kit and didn't have the revised version un
Read less
-
Richard from Greenville, NH
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
322 of 345 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 2% of time
This inlet hose washer, also known as a high pressure inlet hose washer, is used in washing machines, refrigerators, freezers, and dishwashers. The function of this part is to create a watertight seal in the appliance. If your gasket gets dry and brittle over time it will start to crack and will lose its function. In this case, it is important to replace it. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance. As a safety precaution, remember to unplug your washer from the power source before beginning.
$
8.00
In Stock
PartSelect Number PS11757437
Manufacturer Part Number WPY013783
Fixes Symptom 2% of time
$
63.26
In Stock
PartSelect Number PS2003344
Manufacturer Part Number 12001807
Fixes Symptom 2% of time
$
36.54
Special Order
PartSelect Number PS11739421
Manufacturer Part Number WP22003262
Replacing your Maytag Washer Tub to Pump Hose
Customer Repair Stories
leaking water
removed one panel and front door to access under tub.leak solved!!!! thanks
-
richard from amston, CT
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
2 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
leaking water
Opened a small door in the rear of the washer and loosen the two braces with a screw driver and pulled the old hose and replaced with the new hose replace the door and that was all.
-
JOSE from HACIENDA HEIGHTS, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
7 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
This part may differ in appearance, but still functions same as original.
$
46.59
In Stock
PartSelect Number PS11739534
Manufacturer Part Number WP22004477
Customer Repair Stories
Increasing water leak
The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel
... Read more
above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.
Read less
-
James from Scotts Valley, CA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
11 Clamp
Fixes Symptom 1% of time
This clamp is sold individually.
$
7.43
In Stock
PartSelect Number PS11742760
Manufacturer Part Number WP489503
12 SEAL-TUB
Fixes Symptom 1% of time
$
32.50
In Stock
PartSelect Number PS11739329
Manufacturer Part Number WP22002077
Customer Repair Stories
leaking water at the seal between the drum and door assembly
I took the door off, front panel, soap dispenser(to lift the top out of the way)and took off the cross braces on the front of the machine. I pealed the door bellows off and took the drain hose apart; there was much gunk and debris to clean out...maybe something here was clogged? Removed all the snap clips and took the front of the tub off
... Read more
;the tub seal seemed good, but lots of grime/gunk build up.I cleaned all surfaces, put the new tub seal on,and put it all back togther. The hardest part was working the snap clips back on; I worked a few on both sides, top and bottom, and then filled in the rest. The machine has been working fine for a month now, no leaks:)
Read less
-
max from antioch, IL
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers, Socket set
6 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
This hose can handle hot or cold water and is five feet long.
$
21.53
In Stock
PartSelect Number PS11746820
Manufacturer Part Number WP89503
Replacing your Kenmore Washer Inlet Hose - 5 FT
Customer Repair Stories
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
-
Jimmy from MEMPHIS, TN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
2 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking water inlet hoses.
Removed the old hoses and screwed on the new hoses.
-
Helen from NASHUA, NH
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fixes Symptom 1% of time
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.
$
149.05
In Stock
PartSelect Number PS11740556
Manufacturer Part Number WP25001052
Replacing your Maytag Washer Drain Pump - 120V 60Hz
Customer Repair Stories
Broken Pump
Roll washer out of drain pan on section of 3" PVC pipe. Unplug washer & disconnect hoses. Remove rear access panel with nutdriver. Disconnect wiring harness from pump. Disconnect hoses from pump using screwdriver and pliers. Twist pump counter-clockwise to separate from bottom of washer housing. Transfer electronic component from old
... Read more
to new pump. Install new pump in reverse order as above.
Read less
-
Drake from Crofton, MD
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
21 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Pump Stopped Draining The Machine- Impeller In Pump Wore Out
First- I unplugged and completely drained machine of water by putting hose at ground level near drain . Second- removed back plate to washer saving all hardware. Third- disconnected in and out hose to pump. Twisted pump gently as to pop it out of slots in bottom of machine. Fourth- disconnected wires to old pump hooked to new pump
... Read more
replaced pump, replaced hoses- tested machine then replaced back plate of machine. Done.
Read less
-
Deborah from Westfield, MA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Pliers, Screw drivers
79 of 87 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
15 Clamp
Fixes Symptom 1% of time
This screw-type clamp, also known as a hose clamp, is made of metal and is used within various models of washers to secure the tub-to-pump hose and tub/drum of the washer. Without this clamp, the hose is vulnerable to leaking and disconnecting from the tub during the wash cycle of the washer, which can present a serious safety hazard for the machine and your home. Clamps can wear out and lose their tension due to excessive vibrations, mechanical damage, and normal wear and tear, all things present within a washing machine. To replace this clamp, you will first need to turn off your washer and you will need access to the lower portion of the washer chassis, which may require one or multiple screwdrivers and wrenches. Once you have access, use your screwdriver to loosen this clamp, which can then be removed and replaced with the new clamp, which will need to be tightened securely. Then you can simply reassemble the rest of the washer you originally disassembled.
$
7.29
In Stock
PartSelect Number PS11743796
Manufacturer Part Number WP696392
Fixes Symptom 1% of time
$
39.91
On Order
PartSelect Number PS11739415
Manufacturer Part Number WP22003075
Fixes Symptom 1% of time
$
21.32
Special Order
PartSelect Number PS11739331
Manufacturer Part Number WP22002099
18 HOSE- INJE
Fixes Symptom 1% of time
$
87.74
In Stock
PartSelect Number PS11739330
Manufacturer Part Number WP22002083
Customer Repair Stories
water leaking around washer
First ya have to find the problem that takes time.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, fo ... Read more und the crack ordered if from you guys.(very fast) slapped it in and put a load in.
Pulled the front off via the four screws, two on the door and two on the opp side. Removed the two top hold down brackets that hold the top on (on the front), popped out the four screws for the detergent and the top hinged up, The hose was right there. Removed the two hose clamps, fo ... Read more und the crack ordered if from you guys.(very fast) slapped it in and put a load in.
Read less
-
Dennis from Bethel, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
5 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!