MAH20PNAWW Maytag Washer - Instructions

Followed the instructions that were supplied with the Lip Seal Kit, for removal of the inner drum. As expected, once into the project, I found that the bearings that are part of the outer drum, were bad. Reading other installation blogs, prior to starting, I knew the bearing sizes, 6206-2RS & 6207-2RS, and I purchased the bearings, from Motion Industries, before starting the project. Taking a hammer and long 1/2" socket extension I was able to remove both the inner and outer bearings form the outer drum. (Bearings were all but seized up) Once I had cleaned up the aluminum hub which is part of the outer drum and where the bearings mount, I was able to start the process of installing the new bearings and completing the project. Timing could not have been any better to take on this repair project because the aluminum hub was showing major signs of corrosion on the inner side of the hub. I was concerned that the new lip seal would not seal off the inner drum from the bearings/outer durm. This project was competed on 8/21/12 and so far and 6 loads later I have not found any leaks.

I had pretty much the same experience as others. Difficult parts were 1) removing the inner tub, I used the blunt side of an axe with a 4x4 after several hammers would budge it. 2) removing the old bearing, like others I had to cut them out using a Dremmel with a steel cutting disk from Home Depot ($15) Wear eye protection as sparks are flying! Cut out the inner race and the bearing fell out, then cut V notches in the outer race, trying not to cut into the bearing seats on the tub although I did have a couple small cuts, then hammered it out from opposite side. Installed the new beaings and metal sleave between (what is the sleave for?). I tapped both bearing up against the seat shoulder but with the sleave in between there's not enough room and the new bearings turned real hard as the sleave is binding them. (Minor panic). A couple taps with hammer and chisel on the inner bearing from opposite side to push it out created enough room and the bearings turned real easy. Suggestion; plug the drain opening in the bottom of the outer tub with a towel or sponge to prevent pieces of the old bearing from falling in there. I saw one ball roll down in drain, so I tipped the machine on its side and several balls washed out plus pieces of the old bearing. I had a towel laying over the top but that wasn't enough, needs to be stuffed down in the opening. Re-assembly was easy and the machine runs perfect. The wife is very impressed. Total investment approx $85 (kit, bearings and cutting disk) plus about 8-10 hours vs $800 repair or new machine.

Repair was simpl, took about 3 1/2 hours +. Used on line video for dismantal information & reassembling. Hammered out old bearings and seals. Installed them with big bolt and old bearings, I used the old bearings as pushing tools for new bearings. The large bolt and nut pulled the bearings in to place at the same time. Installed seal and reassembled machine. I moved from Jester to King at home.

The whole thing is on YouTube beating out bearings was the only difficult part

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.

Thanks to Partselect's accurate parts' lists, and installation video, along with others' posted installation trials, gained confidence to attack problem on my own (coupled with repair (or should I say, "replace")men's advise to trash machine). Bearings had basically disintegrated, causing inner tube to be out-of-alignment, and rub against outer tube. Would just like to add to what others' contributed, that I found Plumber's Tub Drain tool to work very well at knocking-out larger front bearing (was perfect fit to ID of bearing). Had to Dremel cut out rear bearing, but quite accessible from rear of machine. Otherwise, alot of cleaning from 13yrs. of useage. Thanks for everyone's assistance!

The replacement was not complicated. It took me more time because the details are not in the videos and I had to do it twice because I didn't get the seal on correctly the first time. I used the Neptune videos available on you tube for the basics. Use the "inspecting front door lock wax motor" video for a start, but be sure to take off the top front crosspiece also for easier access to the spring that tensions the seal retainer cable. You don't have to disconnect any wires, just lay the door lock assembly gently to the left of the washer. The old seal comes off very easily, using the front loader door seal video. My washer was an early one without the drain tube so I had to get the drain tube and clamps separately and drill out the tub nipple to the left below the seal. I used the biggest drill bit I had that fit inside the nipple. The tub is plastic and very easy to drill. Most of the plastic shavings will come out toward you if you drill slowly and don't push too hard on the drill. I also used my shop vac to try and get out any other shavings. I used dish washing liquid as a lubricant to help put the seal on and used too much. It doesn't take very much. The spring that tightens the inner seal clamp/cable was very hard to attach and it did require two locking pliers [vise-grips] and quite a lot of effort. You have to hook one end of the spring to the cable that wraps around the seal, hold the other end of the cable with locking pliers, the free end of the spring with locking pliers, and stretch the spring to hook it to the free end of the cable. There are some other methods described in various forums and one of them might work better for you. When I was an auto mechanic we had a special tool that helped attach springs like this on drum brakes. I was sure wishing that tool was still in my tool chest but it was not. This was the most difficult part for me, getting the cable and spring all in place and stretching the spring without dislodging the seal and having to start all over.I didn't get the seal aligned correctly the first time and had to do it over after putting ever thing back together and washing a load of clothes. I could have avoided that by carefully inspecting the seal before I put everything together. When you put it back together the end of that red or green nylon line that looks like weed eater line goes under the soap/bleach dispenser bezel on the top so you can manually open the door if the wax motor goes bad and it won't unlock.

Followed the PartsSelect video for the seal replacement, which was step by step and spot on, I just had to add the bearing replacement part myself. Once it was dissembled I drove each bearing out by tapping them with the hammer and drift. My model had no bearing retainer ring. I did not remove the outer drum from the washer. Clean the aluminum hub real well, scrape it with a utility knife to remove corrosion, wipe with a solvent soaked rag, etc. I disagree with other methods ive seen while researching, like a wire brush in a drill, because you will remove aluminum material from the hub and the bearing wont fit as tightly as designed. tap in the rear bearing til fully seated. I did the rear first because gravity then held the spacer in place. Set the spacer in place, noting that one end is "flared" to a larger diameter, so it seats against the larger race of the front bearing. Align and start the front bearing in place. The spacer needs to align with the bearings so it bears against the inner races of the bearings. So to hold it in place I rolled up a piece of light cardstock, slid it thru the spacer and bearing, and as it "uncoiled" it aligned the spacer. Pretty well. I did have to tap the spacer a little with the drift after the bearings were in, but just a little. After that, back to the video for the seal and reassembly. Only other comment I have is to locate the bearings early. I ended up going to grainger for one and Napa for the other. And no one could seem to cross the "DU" part of the original NGK bearing. The DU means it just has seals on both sides. Pretty standard stuff. That could have been easier. Also hold off ordering extra parts. I have found PartsSelect is really quick getting stuff out. I ordered an inner drum because i heard from other research that that could cause the banging noise. My banging noise was from one bearing disinegrating and the balls breaking up inside the hub. Shipping the drum back cost 70. UPS wanted 160. So that could have gone better, but I didn't want to let the machine sit too long. Next time I'll let it sit a couple days.

I was sick when I heard the noise from our washer. I looked online at new ones and found out it was going to cost between $1000 to $1500 to replace it. While looking online I found the PartSelect site. Unbelievable! I put in the model #, read the posts, ordered the parts and within a few days they were in. Using the video and the posted instructions I took it apart and replaced the bearings and seals. The whole thing took about 3 hours and we were back to washing clothes. Total repair costs were about $160 to $180. Compared to the price of a new washer, you guys saved the day.

Following the information on the web it simplified this repair a great deal. Disassembled the front of the machine, then pulled it out from the wall, removed the rear panel. Removed the belt & pulley and knocked the shaft loose from bearings. Removed the tub and using the brass bar drove the rear bearing out first then removed the seal and front bearing. The seal has to come out first so the plastic spacer can be removed, used the brass bar from the rear of machine to drive front bearing out. Cleaned up all parts and reassemblied. Replaced the motor isolators and drive belt with new since I was in the machine that far. Removed the soap & bleach tray and cleaned up all those parts. re-assembled and washed a load of rags to test machine. Sounded like a new machine. Sourced the new bearings from a bearing supplier they are 6200 Series bearings, Rear 6206-2RS; Front - 6207-2RS. Had I not made this repair I would have been buying a new washer & dryer so this job for a little over a hundred bucks saved me thousands! Thanks to PARTSELECT for all this information!!

I referenced the enclosed instructions, and U tube videos, along with gasket I also changed the bearings for about $40. From local grainger, it seems to have solved problem, thanks for quick shipping,

Moldy bellow was the reason I replaced the bellow. It tried cleaning the bellow numerous time over the last five year, but once the mold sets in, it's a losing battle. A highly mold resistant bellow would be nice. The available video was invaluable. I would not have purchased the parts if I had not seen the video. I spent a few more dollars for additional parts, because once I got started I did not want to find a bad part and then not be able to complete the repair in one try. Since the bellow was moldy, I expected the door boot drain hose would be moldy also, so, for a few more dollars, I replace it also. Worth the effort. I took me, just under two hours to complete the job, with the help of my wife. I'm some may be thinking, what did she do? She cleaned the parts I took off, so they were clean, well at least cleaner, when I put them back on. This washer was nearly ten year old and had never been apart. I could have finished the replacement bellow in less than an hour, but I took some time to clean inside the washer while it was apart. That's just the way I roll. Fitting the bellow to seal properly was not as simple as the repairman made it look on the video, but that was because he had done this before, probably many time over. He knew what it felt like to fit it and snap it into place. Once I got the feel of seating the bellow, it went smoothly. The boot cable and spring are a bit tricky to hook, as anticipated; I read some previous experiences. So, I thought about how I was going to secure the spring in order to stretch it to the other cable hook. I decided to use two pairs of vice grips to hold the spring and cable hook end. I have two small to medium sized vice grips, which worked perfectly. Otherwise, it is very difficult to pull and hold a pair of pliers closed, at the same time. I sit at a computer most days and am not used to a mechanics world. Use your brain when you don't have the brawn. Job done, no leaks.

First and foremost, disconnect the power before anything else, then remove the door, access panel, and front of the washer,I then detached the front of the rubber boot so I could remove the plastic panel that it attaches to, that exposes the springs, I then used a vice grip to remove the springs replacing them one at a time, I also replaced the struts in the rear of the machine which requires removing the rear panel, and I used a bottle jack to support the rear of the washer tub while I changed the struts, I changed the struts first which only helped a little, the springs made the job complete and the washer now completely wrings the clothes to a damp state that dries quickly.

Replaced the belt and motor isolators. Watching your video made it very easy.

remove door with Phillips remove front panel nut driver remove soap tray lid and lift up top Phillips test small contactors for continuity and replace removed locking sprocket and replaced