MAH14PDBEW Maytag Washer - Instructions

removed one panel and front door to access under tub.leak solved!!!! thanks

Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!

removed door,Opened the front panel, opened the top and proped it out of the way. Pulled the boot from the front cover disconnected the drain, released the boot clamp and pulled the boot off. I cleaned the inside of washer and soap tray. cleaned debris from the drain hose. repaired a broken soap dish connection. changed supply hoses and new valves. Generally checked cleaned and overhauled the washer.

Bought the parts and just inserted them.

Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.

Download machine service manual from internet. This makes dismantling easy and prevents damage to component parts.

Dismantle as per manual and remove old bellow - easy.

Re-install new bellow on tub rim - EXTREMELY difficult. The spring that tensions the wire that holds the bellow in place is extremely powerful and in attempting to stretch it it often slips off the tub rim taking the bellow with it so you have to start all over again. It took me 2 hours to realise I would never be able to do this alone. With the help of a second pair of hands this was accomplished in 20 mins with some difficulty.
The rest of the installation and re-assembly was done without difficulty.

Basic disassembly as described earlier.Some tips I found helpfull. Use vice grip pliers on spring.it will keep a grip on the spring hook and you can exert more force to pull the spring.Th bellows was very sticky and hard to slip into place. I put a litle silicone lube ( stuff you use for pool pump gaskets )on the bellows. It made it slip into place easly.

Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.

Despite the reviews by people who installed this part themselves, I knew that any type of repair was beyond my ability. I enlisted the assistance of a cousin who is a trained, professional appliance repairman. Despite not having instructions, with his experience things went well until he found he did not have the unique wrench that would have made life easier, but he was able to adapt and use the tools he had at hand. Unfortunatley, after more than twos hours attempting to install the wire around the boot, he realized that he could not do it alone, I had to help him and together, we were able to install the wire. It would have been helpful to have step by step instructions and a list of necessary (or at least useful) tools.

Wow! Thanks to the customer info/hints already posted the repair went super smooth and was relatively easy to accomplish. $70.00 for an easily replaced part sure beats $1,000+ for a new washer. Super fast shipping reduced down-time significantly!!! From start to finish the job took less than 30 minutes. Thank you so much.

Removed the door and front panel with ease. Then came the spring and cable. People who say it was easy are not telling the whole story. Removing the spring was okay except for it flew across the room. Putting the new cable on with a pair of needlenose pliers did not work for me. I had to get a spring tool like you use on brakes on a car. Once I had the tool and secured the cable in place with a piece of wire I got the spring on. Everything except the spring took about 15 minutes.

The whole thing is on YouTube beating out bearings was the only difficult part

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.

My first time attempted to repair washer and step by step video instruction attached with order confirmation did it for me. Thank you

Set my iPad on the dryer and played the video. Could not have done it without it. Putting spring back on was the hardest, fell off once. Took that long because video connection timed out and had to get another coffee. Part delivery was quick. Found the drain tube out of the bellows was clogged. If it wasn't for the mildew on the bellows could havw fixed the problem if I had known about a drain at the bottom of the bellows.