MAH14PDBAW Maytag Washer - Instructions

removed door,Opened the front panel, opened the top and proped it out of the way. Pulled the boot from the front cover disconnected the drain, released the boot clamp and pulled the boot off. I cleaned the inside of washer and soap tray. cleaned debris from the drain hose. repaired a broken soap dish connection. changed supply hoses and new valves. Generally checked cleaned and overhauled the washer.

Our rental house washer had the parts removed by the last tenant, just replaced them. Thanks!

removed one panel and front door to access under tub.leak solved!!!! thanks

Bought the parts and just inserted them.

Loosened the hose coupling, removed the old washer and strainer; cleaned the opening; flushed the opening; installed new strainer and washer; reattached hose and "Bob's your uncle"! No problem.

Wow! Thanks to the customer info/hints already posted the repair went super smooth and was relatively easy to accomplish. $70.00 for an easily replaced part sure beats $1,000+ for a new washer. Super fast shipping reduced down-time significantly!!! From start to finish the job took less than 30 minutes. Thank you so much.

Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.

Basic disassembly as described earlier.Some tips I found helpfull. Use vice grip pliers on spring.it will keep a grip on the spring hook and you can exert more force to pull the spring.Th bellows was very sticky and hard to slip into place. I put a litle silicone lube ( stuff you use for pool pump gaskets )on the bellows. It made it slip into place easly.

Download machine service manual from internet. This makes dismantling easy and prevents damage to component parts.

Dismantle as per manual and remove old bellow - easy.

Re-install new bellow on tub rim - EXTREMELY difficult. The spring that tensions the wire that holds the bellow in place is extremely powerful and in attempting to stretch it it often slips off the tub rim taking the bellow with it so you have to start all over again. It took me 2 hours to realise I would never be able to do this alone. With the help of a second pair of hands this was accomplished in 20 mins with some difficulty.
The rest of the installation and re-assembly was done without difficulty.

Despite the reviews by people who installed this part themselves, I knew that any type of repair was beyond my ability. I enlisted the assistance of a cousin who is a trained, professional appliance repairman. Despite not having instructions, with his experience things went well until he found he did not have the unique wrench that would have made life easier, but he was able to adapt and use the tools he had at hand. Unfortunatley, after more than twos hours attempting to install the wire around the boot, he realized that he could not do it alone, I had to help him and together, we were able to install the wire. It would have been helpful to have step by step instructions and a list of necessary (or at least useful) tools.

Removed the door and front panel with ease. Then came the spring and cable. People who say it was easy are not telling the whole story. Removing the spring was okay except for it flew across the room. Putting the new cable on with a pair of needlenose pliers did not work for me. I had to get a spring tool like you use on brakes on a car. Once I had the tool and secured the cable in place with a piece of wire I got the spring on. Everything except the spring took about 15 minutes.

I had pretty much the same experience as others. Difficult parts were 1) removing the inner tub, I used the blunt side of an axe with a 4x4 after several hammers would budge it. 2) removing the old bearing, like others I had to cut them out using a Dremmel with a steel cutting disk from Home Depot ($15) Wear eye protection as sparks are flying! Cut out the inner race and the bearing fell out, then cut V notches in the outer race, trying not to cut into the bearing seats on the tub although I did have a couple small cuts, then hammered it out from opposite side. Installed the new beaings and metal sleave between (what is the sleave for?). I tapped both bearing up against the seat shoulder but with the sleave in between there's not enough room and the new bearings turned real hard as the sleave is binding them. (Minor panic). A couple taps with hammer and chisel on the inner bearing from opposite side to push it out created enough room and the bearings turned real easy. Suggestion; plug the drain opening in the bottom of the outer tub with a towel or sponge to prevent pieces of the old bearing from falling in there. I saw one ball roll down in drain, so I tipped the machine on its side and several balls washed out plus pieces of the old bearing. I had a towel laying over the top but that wasn't enough, needs to be stuffed down in the opening. Re-assembly was easy and the machine runs perfect. The wife is very impressed. Total investment approx $85 (kit, bearings and cutting disk) plus about 8-10 hours vs $800 repair or new machine.

Repair was simpl, took about 3 1/2 hours +. Used on line video for dismantal information & reassembling. Hammered out old bearings and seals. Installed them with big bolt and old bearings, I used the old bearings as pushing tools for new bearings. The large bolt and nut pulled the bearings in to place at the same time. Installed seal and reassembled machine. I moved from Jester to King at home.

The whole thing is on YouTube beating out bearings was the only difficult part

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.