Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This is a genuine OEM leveling leg for various models of LG ranges. This leg is used to stabilize and support the range, and if damaged, broken, or missing, will cause your range to rock back and fort...
Upgrade your oven with this durable gliding shelf rack, designed to provide a stable surface for baking, roasting, and broiling. Its smooth sliding design makes it easy to insert and remove dishes, of...
This oven base plate and bottom heat shield is designed to protect the lower section of the oven from excessive heat while providing structural support for internal components. Positioned at the base ...
This oven inner door glass panel is designed to replace cracked, broken, or damaged interior door glass and restore proper oven performance and safety. Made from heat-tempered safety glass, the panel ...
Go onto youtube, such as https://www.youtube.com/watch?v=-ITkrwhDNMQ and watch similar videos for DYI. The process is very similar to other models.
Once the door is removed, place oven door on a towel or soft place so it does not scratch the door. Unscrew the screws and make sure you notice where each screw goes, so you know
... Read morethe process of where each screw goes when you re-assemble.
Once the inner cover is removed, remove the insulation, too so you don't damage it. Use Wet/Dry Shop Vac to clean the shattered glass. (WORD OF ADVICE: I did not remove the insulation and the suction of the Shop Vac removed part of the insulation, so now instead of a quick turn around repair turns into a few weeks repair, because the insulation is on back order 10-14 days from the supplier. DON"T MAKE THE SAME MISTAKE!)
Once the glass has been removed, the new inner glass is replaced, begin by re-assemble the oven door with the correct screws and attached the oven door to the range.
i removed the oven door by lifting the safety latches on each hinge and gently lifted the door off. once off i could access the 2 large phillips head screws and loosened and removed them. then i simply slid out the old and slid in the new & reversed the process.
After consulting with multiple specialists, watching several videos/ tutorials online and trying multiple cleaning tools. They all coincided that if the stove was not wet and it is making that noise, It could be a problem with a switch board or the computer of the range. Ordering the part was the easiest part (and trust me, i am not a fix
... Read moreer or an expert on doing any repairs). However, PartSelect offers you precise parts if you know what you are looking for and have the correct model. The problem? Well, LG and Samsung ranges are known for their cook top being hard to dismantle and you need to remove a few pieces before you can get under the knobs where the switch boards are. It took a lot of time to just do that. The connection is a bit complex and I would suggest to leave it for an expect to do it. I must say this… i am glad that i have tried to work on the switch board before i started ordering parts that I did not need. I have over 5 hours with the range plugged, since i have switched the switch board and so far, it is not making that clicking sound. Ps. An expert was charging me from $180-250 to do an inspection and to order the part I needed and an extra fee for installing it. I certainly saved some money by just doing it myself.
