Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This dryer drum belt (Whirlpool Dryer Belt, Drive Belt) has four ridges, three grooves and is 1/4" wide, and 92 1/4 inches in length. It comes in black and is made of rubber. The belt transfers the ro...
This is an OEM lint filter for a dryer. This lint filter screen has two side guides on either of the screen. One measures 3/8 of an inch wide, while the other measures 5/8 of an inch wide. This part i...
The high limit kit comes with three separate thermal fuses for dryers. One electric thermal fuse with a limit of 258, one gas high limit at 240, and one gas and electric high limit thermostat with a l...
This door catch kit is designed for use in dryers. This is an authentic OEM replacement part. This catch assembly ensures the door of your appliance will close, and remain closed. It allows your appli...
The rear dryer drum roller functions by holding the drum in place while the drum rotates on support wheels during the drying spin/tumble cycle. Included in this rear drum support roller kit are four s...
This high limit/safety thermostat is used on many gas and electric clothes dryers. It is made of metal, and is almost two inches long. With this thermostat, a dryer's heating element will cut out if t...
The drum felt seal, used in dryers, allows the drum to smoothly glide with minimal friction. If any of the following symptoms occur with your dryer, replacing the felt seal can be a solution to your p...
I pulled out the broken lint filter and put the new one back in, real easy. I am so happy with the prompt delivery I got from PartsSelect.com. I ordered on a Monday and and it was delivered on a Wednesday
1. Unplug dryer from power outlet 2. Lift dryer top from front (hinged in rear). Just friction holding top down. Use flat scewdriver wrapped in cloth to help lift. 3. Locate heating element - rear top behind drum 4. Unplug red wires to the high limit thermal fuse 5. Unplug red wires to the heating element 6. Unlug
... Read more white wires to the high limit fuse 7. Remove high limit thermal fuse 8. Remove heating element 9. Remove high limit fuse 10 Clean heating box Installation is reverse order but do the following first! Clean lint trap - Remove front of dryer 1. Unplug white door switch wires. inside front top right 2. remove two screws securing the front of dryer - inside front top left and top right. Front of dryer is hinged at bottom 3. Clean all the lint you can find. If you have never cleaned out the lint, there might be a lot and the cause of over heating (shorting fuse life). Add to your yearly things to do list. 4. While your at it check the alignment of the plastic glides the drum sits on. 5. Also check the foam gasket between the fan housing and lint trap. Mine was off a bit. Realigned with doubled sided tape.
1. Removed the screws from the lint catcher 2. Removed the bolts from upper rear of dryer 3. Pried off the dryer top from the front (it rests on rear hinges) 4. Disconnected dryer door wiring 5. Removed bolt from inside upper front corners; removed front panel (be careful: the edges are sharp and the tumbler will fall
... Read morewhen it loses support) 6. Removed broken belt and lint from interior parts; removed tensioner (which had fallen out of place). Note: The newer models have a tensioner pulley; my older model had a smooth semicircle that was confusing at first glance 7. Flipped dryer onto its back (for easier reinsertion of new belt and tumbler) 8. Placed new belt on tumbler; reinserted tumbler 9. Inserted new belt through tensioner, inserted tensioner "legs" into grooves on floor. Note: The belt will pull the tensioner upright when it's inserted properly (which isn't obvious at first) 10. Made sure belt and tumbler seal were properly installed 11. Replaced parts in reverse order The process took over an hour because I couldn't figure out how to insert the belt through the tensioner. The trick is to insert the folded belt through the tensioner and onto the motor pulley. If I had to do it again, it would take about 30 minutes (including cleaning lint)
![Replacing the Multi Rib Belt - 92-1/4"](https://img.youtube.com/vi/PF90f-1kdNY/maxresdefault.jpg "Replacing the Multi Rib Belt - 92-1/4"")
![](https://partselectcom-gtcdcddbene3cpes.z01.azurefd.net/346995-1-S-Whirlpool-341241-Multi-Rib-Belt-92-1-4-amp-quot.jpg "Multi Rib Belt - 92-1/4" – Part Number: 341241")