LMV1683ST LG - Instructions

Took old ones out, threw away and put new ones in easily.

Unplugged the microwave. I opened the door. I used a butter knife to pop the bezel off the inside of the door. I pushed the locker up and to the left and used the butter knife to pry it loose. Disconnected the locker from the spring, and reversed for the installation.

Read the troubleshooting section on this site. Figured it was an interlock problem because the food was not getting hot (magentron not turning on) and the carousel was not turning. Did not think both the carousel motor and magnetron failed at same time, thus indicated an interlock problem. The interlock switches are actuated by the door latch. Replaced the assembly locker piece with all three switches (only a $20 dollar part) and microwave was fully operational again. Wife and kids think I am a hero.

Removed the MW from the wall. Took the top screws off the air vent. Then removed the two screws holding on the display. I then moved the display to its side and it revealed the micro switches. I removed the plug in leads from the micro switch one at a time. I did this with all three micro switches only one at a time. I reinstalled everything and plugged it in. No more fans starting when the door is opened.

Removed outer cover

removed lower door switch

installed new switch

Wa La!

WORTHLESS...I EMAILED YOU ON 2/7/22 AFTER RECEIVING THE DAMAGED FILTER DUE TO NOT SHIPPING IN A HARD OR SOMETHING IN THE ENVELOPE TO PROTECT THE FILTER FROM BEING BENT.
I HAVE NOT HAD ANY RESPONSE FROM YOU FOR THE DAMAGED FILTER OR WHEN I CAN EXPECT ONE THAT I CAN USE.
UNSATISIFACTORY SERVICE!

Replace (after testing w/ohm meter) diode and locker holder. My door often would not close properly. Microwave let know by saying not shut properly. When disassembled found the top screw mount was hollowed out resulting in it moving on occasion when you close door. First remove casing (special safety torx head) needed for rear screws. Onc e removed all parts available to view or work on. Diode is on the capacitor so caution is needed when removing. Serious shock hazard if touched. Use insulated pliers to remove from capacitor and a phillips on the ground. Test with ohm meter Should have resistance on way and non the opposite. Replaced mine bad. Next the holder 2 phillips screws and its yours. Unplug each switch and remove. Take note to what wires go to what switch and what switch mounts where. Mine had 3 switches. Removed from old holder and put in new. Screwed holder back in place and left scrws loose till re wired. Once wired set the holder by lightly tighting the screws. Try the door till it seats properly ensuring that all 3 switches are working properly. If so thighten screws. If all seems to work as advertised, safely plug in and test unit if heats up un plug and put cover back on micro. Your all set. Happy heating.

removed old cover put the new one in place found right size screw from my tool box, tightened it.

I followed an old appliance repair forums post from 2008 that discussed this exact common issue with this LG model. It took me quite a while to find the info. Then I used the schematic diagrams on your website to find where the part was located inside the microwave. I removed the outer cover. I tested all components including the thermostat for continuity with a multimeter. I discovered there wasn't any continuity in the thermostat so ordered the part and replaced it. Everything works like a charm! Thanks for the great, fast service.

Followed owners manual instructions to the letter: removed two top screws, opened the unit door so I could slide out the old filter. We don’t cook much at all in the unit, mostly just heating coffee and reheating leftovers. BUT! The top grill was pretty greasy and needed hot soapy water to clean, including in the depths of the top area. The whole process, especially the company website for part ID and purchase, was slick!

I just wait for the part to come, swap it and voila, FIXED! thank you guys

Use a ladder.
Remove the broken part if it’s not already off.
Remove and save the screws from the top of the microwave.
Unwrap assembly and insert it into the gap aligning the points.
Screw the screws in.
Verify fit.
Done!

Both were easy to replace. I followed the instructions in the users manual which came with the microwave. On the grease filter, I removed the 2 Phillips head screws which hold the grill plate in place. I had to open the microwave all the way to remove the grill plate. The grease filter was easy to remove and replace with a new one. I then put the grill back in and secured it with the 2 screws. Easy Peasy!

You just pull out the clip but the the hard part is doing that without bending the metal hole the holds the clip. If you do bend the hole the clip will not fit flush. Just get a flat screwdriver and reshape the whole.

Removed burned pieces and reinstalled new.