LA5580XPW1 Whirlpool Washer - Instructions

My wife did the repair. Went on your website and watch the video on how to replace the switch and she was able to do it herself. I didn't mind at all. Saved $75.00 service charge.

Just had to screw the new one on.

Screwed the new timer knob on - have slight problem in that the knob is shorter than original and you have to press harder to start/stop - but it works

Unscrewed the old knob part. Screwed on the new knob.Took less than 5 mins.

I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred the bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.

1) Using a Phillips head screwdriver, the two screws retaining the hinge pin to the lid were removed. 2) Remove hinge pin and tilt lid slightly to gain access to bushing hole. 3)Install new bushing in hole. 4)Reposition lid. Insert hinge pin through lid and into bushing. 5)Reinstall hinge pin retaining screws and tighten.

Both the latch on the door and the strike plate were replaced. A technician from Parts-Select came and leveling and removal of possible obstructions were done. It looked like it might stay closed but popped open with temperature additions during the wash cycle. The door seals had been replaced and probably were putting some additional pressure on the door. I inserted the "magic bullet" --- (a screw) in above the strike plate and that solved the problem---door stays shut. As a side note, the screw originally used was inserted in an electrical wire plastic connector and inserted but it appears that shutting the door too hard caused it to pop into the cavity behind the latch (not into the washer itself). So I used a plastic sheet rock anchor with large spiral threads which was a larger diameter than the strike-plate slot and therefore when the door was shut hard there was no way that it could be dislodged. It was a smaller size anchor in order to not put excessive pressure on the stike-plate. Since the plastic anchor had a phillips head slot I did not have to use a metal screw to get the anchor in.

Oredered late Friday afternoon. Got part Monday afternoon.thanks

Bought new knob an screwed it on. Could not believe I could do this with a 20 year old appliance.

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.

I was impressed with the fast time the part was delivered. The price was good too. The installation video and instructions did not match my dryer but it was helpful to some extent. The video and instructions being different was not ya'll's fault because of the age of the dryer. It took me so long to change the switch was because of the location and design of the switch. I got it though.

Had a lot of corrosion on the shaft area and had a hard time removing the inner tub but after some WD-40 and unprintable words and labor it popped off. Cleaned everything up, shaft, inner drum and outer drum. After that everything was a piece of cake. Thanks for the help!

This repair took me longer because I was just giving it a try - I have no experience, although I tend to be "handy." I'm sure anyone with experience would rate this as "easy" and have taken only a short time. I had to watch the video several times to understand what to do - and the comments were helpful too. My washer is an OLD maytag, so I removed the front of the dash and pulled it forward to access the electronics. My switch had only 2 prongs, so I hooked up to the "lid closed" option on the new switch. It works perfectly now. Very pleased I gave it a try.

I found on youtube that there are directions to repair. Dryer problems are usually one of three things, the door switch being one of them. i checked this last (should have been first). ordered the part( about 65% off sear's cost) and it came in one day! It went on really easy as long as you knew from repair video how to access inside. almost spent $400.00 on a new one.