KUDS30FXWH0 KitchenAid Dishwasher - Instructions

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

Prepared by watching the video. Great instructions. Great.

Disassembled easily as per video. Removed the old latch and installed the new.

Began the reassembly and learned that after ten or more years the small plastic parts used to keep the dishwasher steady had slowly deteriorated to the point that I was breaking these necessary items faster than I was putting the appliance back together.

What was a half hour task became over two hours and the end result was for me to put my tools away and buy a new dishwasher the next day. I learned that if your appliance is over ten years old BUY A NEW ONE!

Great job by the people who make and sell the latch parts for you who own a dishwasher that is only a few years old.

Thank you Part Select.

Turn off breaker to dishwasher.
Remove lower basket.
Drain any water using a wet vac.
Remove bottom cover plate. Should be 2 plastic screws using flat head screwdriver.
Should be able to reach pump. Turn counter clockwise to remove.
Disconnect plug wire on pump.
Install new pump by turning clock wise.
Reattach wire plug.
Run a wash cycle with empty dishwasher and check for leaks.
Replace cover plate.
Done.

put new hose on, very easy.

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

Remove 2 screws on lower baseplate. Remove 2 screws that hold dishwasher inside cabinet( may be attached to counter top or side cabinets). Turn off water supply to dishwasher. Remove any connections such as water supply, electrical connection, or waste water line that prevent dishwasher from being pulled out about 3/4 of the way. With the dishwasher door closed, remove broken parts and replace with new parts. Pull on spring to make final connection of nylon cable. Reverse the above instructions for re-installing the machine.

I removed and reinstalled the new gasket per the video instructions, but I found the corners to be much harder to install than indicated. I finally used a large, flat, dull screwdriver to carefully push the gasket all the way in, and used my fingers to feel whether the gasket was all the way in. I figured if the gasket wasn't all the way in, I would have a leak at the bottom of the door because the top of the gasket would stick out farther than the bottom, which is exactly what the original symptoms were. Perhaps I didn't need a new gasket? There was no visible damage. Pushing in the corners of the original gasket may have fixed it, but the new gasket worked perfectly! Thanks, Part Select!!

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

Watch your video about my dishwasher symptoms. Move water tube for upper rack to the right and release lower spray arm. Remove 4 clutch head screws from filter cover and remove. Dig out 10 years of undisolved soap and reassemble.

I took the unit apart to find out what was making the loud noise and found the seal on the main pump had been leaking ito the bearing on the motor.

Removed the old hose, after loosing metal looking rings. Installed new hose ad finally tight firmly the looking rings, using wrench and socket.

disconect water supply and drain hose, unscrew 2 screws hoding front of dishwasher to countertop, slide dischwasher out so you can tip on its door and remove 1 screw hidden behind plastic shield and pull motor out install in reverse order.

Remove the mounting screws that hold the dishwasher under the counter top. Remove dust cover plates at the bottom of the machine. The machine will have to be pulled out, so turn off the water to the machine. Usually under the kitchen sink. Disconnect water supply and push it out of the way so the dishwasher can be pulled out. Pull machine out enough so you have access to the door cables and springs. The door will have to be in the closed(up) position to do the repair. Usually only one side is broken. Start with the broken side and copy the working side when installing new parts. Then repair the working side. To get the working side apart just pull on the spring and disconnect it from the cable. Do the reverse to reinstall.

Removed old part and replaced with new part

Removed old tine rows and replaced with the new parts. No tools were needed. Each was replaced one at a time so the old ones could serve as a model for how the new ones were inserted and attached. Not much more complicated than changing a light bulb. Parts appear to be good original equipment quality but quite pricy for these very simple pieces.