KUDS22HT1 KitchenAid Dishwasher - Instructions

I removed the rubber water tube before ordering the part. After receiving the part it took less than 2 minutes to replace the part. Now the dishes are clean!!

I removed the old hose, I lightly coated the id of the new tube with vasoline, both ends, and then heated the oblong end with the hair dryer to soften it and it slid on with litte force. The round end installed without heating.

Removed the old axles and rollers and snapped in the new ones. Really easy repair.

So easy I could do it! I pulled the old tube off (after having dirty dishes for weeks and not realizing it was because of a hole in the hose. When I told my husband I was going to call a repairman, he suggesting ordering the part on line and doing it ourselves - no reason not to! Piece of cake!

Our diskwasher is over 20 years old. The manufacture did not even list the model anymore. Googled - Kitchenaid parts old. Found your site and order the part on Sat. night. It arrived on Wed. Installed as follows that night.
After reading other reviews on how the job went and seeing that people had problems getting the tube to slide on the outlets I decided to take the rack completely apart so as to have unrestricted access to the connections. Would be easier to work the tube on to them.

First I removed the top rack by releasing the two retainers on the upper rack side rails which hold it up. Then I turned it with bottom up and released all of the plastic clips that held the bottom half of the rack in place. If a clip breaks you can use a nylon cable tie to replace it. Then I took out the screw that holds the metal water bar in place and removed it. Then I took out the screw that holds the plastic part that the water bar was mounted on off. Then with the outlet where the tube was to be mounted not connected to anything it was easy to slide the tube on it. I then was able to slide the tube on to the bracket at the back of the rack. Had to use a screw driver to help get the tube over the round outlet. Then worked it on to where it should be. Reassembled the top rack and put it back on the side rails and washed a load. It worked just like it did when it was new. Saved a service call $75.00 and only took about 30 minutes working at a slow pace.
Love it when everything works like it should.

Took off old hose. It practically fell off.
Used a spoon to widen the ends of new hose and twisted on one end, then other end slipped on. Done!

I pulled off the remains of the old tube and simply slipped the new hose on by hand. Easy as pie!

just popped the old hose off and put the new one on. the part was shipped very quickly and I received it within a week even during the holidays

Removed old tube, moistened both ends of new tube with hot water and slid over inlet and outlet holes. Repair done!

I removed the old tube--I had taped over the hole. I didn't quite have the hand strength to fit over the ends and push the new tube into place. So, my husband did that at both ends without a problem. I'm relying on PartSelect for when I need parts for my 13 year-old appliances.

It was simple. I simply replaced the old water tube with the new one you sent, and it works like new. Piece of cake.

removed old hose slid the new one on. Easy one minute job.

Replaced the tube. It was relatively easy although it did take a small bit of squeezing/reshaping the newer rubber tubing to get it to fit on the outlet (it was a bit snug.)

For several years I endured difficulty in pushing in and pulling out a fully loaded lower dishwasher tray in my KitchenAid Superba dishwasher. The tray would "fall out" out of its "track" and jam requiring me to lift up the whole tray to try to pull it out. Then one of the plastic roller "axles" broke and its wheel fell off. So I went on to Part Select's website to find a replacement. When I got it in the mail I replaced the one that broke. I noticed how much more rigid the wheel then ran on its "track." So I replaced all the roller axles and, lo and behold, the lower tray does not jam anymore. It rolls just like new! I am very satisfied. Chris from Bay Ridge, Brooklyn

Took the tube off and noted that there was a factory drilled hole on the underside that lets water drain. I slipped the new tube over the inlet port and the other end over the rotating washing arm aparatus port and everything worked fine. Very easy and fast repair.