KUDI01ILBS6 KitchenAid Dishwasher - Instructions

removed both upper and lower racks. removed lower spray arm(left hand thread) removed "water delivry tube and upper spray arm. removed torx screws on pump cover. removed inner chopper cover. Chopper assy had come apart and was full of food crud. cleaned out and installed new chopper assy. kind of tricky don't force it. reassembled. tested OK.could tell sound of more forceful water pressure

Pulled dishwasher out from under counter. Relaced cord with plastic hook attaching spring to door. Very easy.

Very impressed with Partselect.com. Full schematic of dishwasher made it easy to select part.

Delivered in 1 day. Fantastic. Highly recommend

Lifted out old basket, discarded, and set new basket in place. :-) Rocket science? NOT.

Following advice given on website by previous customers I was able to remove 6 tork screws and check the fuse which was okay. Proceeded to remove the control board and found significant burning on the bottom side. Ordered a new board online Sunday night, shipped Monday by two day Fed Ex, arrived Weds. morning and installed it in less than 10 minutes. Fair price, excellent service and shipping. Thank you and I would buy from you again.

Started as dishes not getting clean and I observed that the top arm was not spinning and there was very low water pressure coming out of the jets. After making sure the water level was up to the bottom of the heating element and making sure the jets were not clogged I checked the filter and chopper. It was a little tough to get the cover off of the chopper but once I did I could see that the chopper scraper was broken off and the shaft was broken. The screen was all clogged up with stuff. Ordered a new assembly and put it in making sure to compress the spring and make sure the gears lined up. Now it is running great.
I think the Kitchenaid is the same as the Whirlpools.

First: Turn power to the Dish washer OFF, then remove the two panels at the bottom of the dishwasher.
Two: remove the Door face panel for easier access to the inlet-Valve.
Three: remove screw that holds Inlet-valve bracket.
Four: slide Inlet valve bracket left and back to get out of slots.
Five: Holding the Inlet-valve forward loosen and remove water line (copper tube nut / pressure fitting).
Six: Remove two wire clips
Seven: Remove platics hose (Spring Clamp)
Replace Inlet-Valve and reverse process///

Got Maintenance Flyer out an read about problem
Removed access plate
Disconnectd water and drain
Removed anchor screws
Pulled unit out and disconnedted from Electric
Flipped on it's back
Ohmed out all heat related items and found discrepency with Thermisitor resistance
Ordered and received Part
Changed out Thermisitor
Checked wiring to Heater and replaced connections
Hooked electric up
Ran Diognostics per Maintenance flyer and cleared fault
Hooked back up and ran like a champ

The reason it took so long is because I put the old thermisitor back in and tryed to run the diognostics just to make sure that was the problem

I watched the instructional videos that showed how to replace the inlet fill hose/water inlet a couple of times. The repair was exactly as shown. No trouble at all.

Turned off water and disconnected line, then disconnected drain, turned off power and slid dishwasher out and turned turned upside down and removed hold down bolt ( it is a 3/8 head bolt) removed wire from motor and twisted motor assembly approximately 1/4 turn counter clock wise and removed old motor and seal assembly reinstalled new motor with new seal and rewired. Turned washer back upright and removed filter assembly and lower jet arm, removed cover for food disposal and reinstalled disposal blade back on pump drive reinstalled cover and filter assembly and jet arm. Slid unit back in place and anchored down to cabinet and turned water and power back on ran washer through a short cycle to clean any soap build up that was left inside and that was it, it all works just like new.

Replaced electronic control panel first which had an obvious defect (burned terminal). Still no power. Replaced fuse and works fine now. Took lots of reading to find out the dishwasher had a replacable fuse. Even the appliance store didn't know.

Via your web-site I was able to download the step-by-step screen-shot pictures. I was really surprised on how easy the detailed photo screen shots made the repair really easy! Thanks for making this repair a piece of cake. If I should ever need additional parts for any of my home appliances I will certainly order my parts through PartSelect.

First I removed the screw from the top water tube and then the upper screw from the vertical water tube at the back of the dishwasher. That gave enough flex to the tube assembly for access to the area I needed to get to, without having to remove it. Then I removed the old spinner retainer and installed the new one. I then snapped the spinner to the new retainer pin, put the tube back into position, and re-installed the screws -- and I was done.

The cycle select buttons on the top of the door worked and would light, however, the power button did not function and did not light. The faulty part ended up not being the control board but the control panel, which included the power button. I spent a good amount of time troubleshooting the problem until I figured this out. The part number was (8531257) Panel-cntl.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Thanks to the previous review of this part, I was able to figure out how to do the replacement myself and saving $150 on a service call. The part is super easy to replace. Remove the screws on the door, lift the outside piece of the door up and off the hinges and then unplug the old piece. I had turned off the electricity to the dishwasher to avoid getting shocked. There were 4 hex nut screws holding the part in, removed those & popped out the old part. Installed the new one, put the door back on and the screws, turned it on and no leaks. This part was so easy to replace, even for a 52 year old woman like myself!