KUDC10IXSS3 KitchenAid Dishwasher - Instructions

Removed bad wheel sets using screw driver to help pry broken part loose. Then just snapped in replacement. Took less than 5 mins. Now it works great.

I found instructions on line when I goggled my dishwasher name and model number with the words noisy door. There were three or four good suggestions at a couple of the sites I visited. I tried applying vasoline, then silicone to the rope where it travels through the plastic guides but that just cut the sound down about 50%. My dishwasher has plastic guides that look like rollers but they don't turn, they are fixed in place. The ropes squeak as the pass over the guides. The replacement part kit has plastic guides that turn like wheels now so the rope does not drag over them and squeak. This repair could be done by me in 20 minutes or less every time now that I know what I am doing.

I removed the black bottom metal cover then turned the nuts on the adjusting (leveling) bolts to lower the front end of the dishwasher so I could pull it out of the cabinet. Once I lowered is as low as it would go I opened the door and pushed down on it which tilts the dishwasher down and you pull out on it and the top lip clears the cabinet. If your dishwasher just pulls out the first time you try these steps may not be necessary.
Once the dishwasher is out the guides and rope are down at the bottom in the front by the door. It's obvious what to do to replace them.

Remove upper tray and spray arm. Remove two screws retaining pipe for upper spray arm and overhead. Unscrew retainer on top of lower spray arm and remove. Gently rotate the upper feed pipe clockwise until pipe can be removed from lower pipe. You may then remove the lower pipe and bearing housing where the seal is. Reverse order for reassembly. I also replaced upper spray arm bushing. Very simple, remove one screw and the arm will come out.

Disconnect the water supply, the drain line, and the two screws that go up into the cabinet frame, then pull the dishwasher out from under the counter. Tip the unit onto it's face and the main pump/motor is facing up. Turn off the power then unplug the electrical connector from the motor. Remove the single bolt at the base of the motor then turn the whole motor ~1/4 turn counter-clockwise. A firm pull will remove the motor/pump at this point.
The new motor/pump has a new seal. See that the arrows on the pump volute and the motor frame are lined up before inserting into the housing. The new motor/pump slides into the housing easily and a 1/4 turn clockwise will pull it in tight. Re-install the locking bolt and revers the rest of the steps to get running again.

.The easiest way to complete the impeller and chopper motor replacement is to disconnect the power, water and drain line, remove the dishwasher from the cabinet, set the washer on its back.

From this point everything is visible, pump housing, motor, etc. and it's a matter of disassembly and reassembly. Make note or a drawing of where all the wires are connected so you reconnect them in the right spots.

Reinstall water lines and power and check for leaks before replacing shield or kick plate.

Cut power and turn off water. Pulled the dishwasher out of the cabinet. Removed internal spray unit. Lay a plastic bag on bottom of tub in case a screw falls from upper spray assembly while removing. Disconnected and drained all hoses. Put down plastic lined tarp on floor. Lay dishwaser on its side onto tarp. Removed hose from recirculation pump, removed water sensor and recirculation pump from housing and detach electric connection. Removed 3 plastic push clips and removed entire motor-pump unit from tub. Position new motor-pump unit into tub. Replace 2 push clips into position, then used a flat screwdriver to put some tension and position plastic pump assembly so I could insert 3rd push clip into position. Replaced all components & reconnect hoses. Turn on water & power. A relatively simple repair. Too bad the original motor-pump only lasted 3 years. Not built like the used to. Thank goodness for Part Select.com Great schematics and descriptions. Excellent website, service, delivery and excellent Part! Thank You!

Rolled out old, rolled in new.

Although the lower rack was a slightly different style than our original, it fit the dishwasher perfectly. We needed to transfer the silverware racks to the new rack and insert one set of removable tines. About 5 minutes and we are very happy with the repair.

The repair was really easy. First disconnected electricity staring with fuses and removing wires from dishwasher, then disconnected drain hose and water hose. Pulled it out and removed pump turning clockwise no need for tools and same way installed new one. Very easy

Was a cinch just watched the video whole procedure took an hr or so

removed old gasket, installed new.
No Leaks!!
Saved the cost of a new dishwashers

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

I followed the PartSelect video to replace the feed tube assembly with spinner and the spray arm seal for the middle wash arm. Washing performance was better, but a couple weeks later the dishes on the bottom rack suddenly stopped getting clean. I decided I probably needed a new chopper assembly, which is identified by PartSelect as the cause of problem for 48% of the cases of dishes not getting clean. Before ordering the chopper assembly, however, I followed the video about how to replace the chopper assembly to determine whether the chopper assembly seemed to be worn out (the video shown at https://www.partselect.com/PS11722146-Whirlpool-W10083957V-Chopper-Assembly.htm). It was worse than I anticipated. I found the holes of the chopper assembly screen blocked by food, and the spinner in front of the screen had broken apart. In addition to finding the pieces of the broken chopper assembly, I discovered a treasure chest of debris, including about 8 pieces of broken glassware, 3 twister ties, a half-inch button, a 3/4-inch screw, and dozens of small pieces of metal. I poured water into the area and used a kitchen baster to suck out the water with all the pieces of debris, finishing the clean-up with paper towels. I ordered a new chopper assembly to replace the broken one, and the part arrived in under 48 hours. I relied on the same video to install the new chopper assembly. The only tricky challenge was getting the new chopper assembly back into place. I first tried needle nose pliers in two sizes, as recommended in the video, but what worked much better for me was using two chop sticks that were each about 1/4 inch square from top to bottom. Needle nose pliers are slanted, but the chopsticks did not vary in thickness and separated the screen from the spinner an even distance apart, making it easier to get the gear shaft on the chopper assembly to align in a straight line with the gear shaft on the pump motor. I also rotated the two gear shafts so the gears of the chopper assembly would mesh correctly with the gears of the pump motor shaft. The video cannot show that step very well because the man's hand blocks vision of how exactly to fit the chopper assembly into place. The video also fails to warn about possible debris around the chopper assembly and to explain how to clean out the debris. After finishing installing the chopper assembly my 14-year-old dishwasher cleaned my dishes as well as a new dishwasher. I spent a total of $110.24 on parts and shipping and invested a couple of hours total. The alternative would have been to spend $800 on a new dishwasher or wash dishes by hand. I am very, very happy with the outcome.

You need to pull the unit out to get access to the spring connected to the rear leg frame. Use the everything in the kit. The rollers are upgraded and will guid the cable better.

pull out the dishwasher
lay it on its side
use a 1/4" drive socket with extension and a universal joint to undo the the hidden bolt,
twist the motor 1/4 turn. this is the hard part you have to pull fairly hard and rock the motor around a little to get the o-ring to let the motor slide out.
lube up the new motor with jet dry or soap and insert back it, turn it back 1/4 turn, install the bolt and plug the motor control wires back in, then reinstall it back under the counter