KSCK23FVMS02 KitchenAid Refrigerator - Instructions

We popped out the new filter and replaced the cap with a twist. It was so easy. It is important to vaccum the front of the refrigerator for accumulating dust.

Actually, the part that was broken was a part that contained the slide that allowed the drawer to pull in and out which was connected to another part that held the drawer to the side of fridge.

I went on line to Kitchenaid.com, clicked on parts which brought me to a PartSelect website that made it really easy to find what I needed. There is an audio instruction guide to help you find what you need. I ordered it and it arrived in the next day or two. To install it I just had to snap it into place. Since I was already on the website I went ahead and order a new water filter.

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

I unplugged the fridge, removed the face plate on the front, disconnected the power feeds, unscrewed the electrical panel and moved it out of the way.
I then dismantled and removed the broken part and installed the new part. I was able to use the rest of the existing parts to get the job done.
I put everything back together, and voila! it works great.

Remove Ice bucket, Remove Phillips screw from bottom of coupling. replace washer, Coupling and screw. replace bucket. very simple.

Searched my issue on the internet then chose part select to see if bi-metal thermostat was available and it was so I ordered part which was under $30.00 incl. shipping. I then went to You Tube to watch how to replace the part but most importantly to find out where it was located and degree of difficulty. Replacement was rather simple and it fixed our 22 year old fridge. I must add that when I looked up the part it also told you what percent of the time that particular item actually fixed the problem based on others experience. I thought that was neat info. as I felt better about ordering something that may or may not fix my problem. Thank you,

Because of the design change of the door hinge it was more difficult to slide the pin into the door and spring. I used an allen wrench to hold it in place on the left side so I could slide the pin in the right hole. Then removed the allen wrench so I could slide the pin all the way. I was very impressed with the time that it took to get the kit. I ordered it about 1:30PM and the following day I had the kit delivered by 6PM. FANTASTIC SERVICE!

Very easy doit repair. Watched Youtube video helpful. Small nut driver and flashlight the only tools needed. Ordered part with standard delivery and received the new motor in under 24 hours! Impressive. I will use Part Select again! So happy to have a working augur. No more stale ice at the bottom of the bin. No more scooping ice with fingers!

Detached the broken ice guide by expandong the opening bewteen the tabs with my hands. Installed the new ice guide and pressed into place. Took about 3 minutes.

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

This one is not rocket science, however, it does take some careful "fudging" to accomplish without additional disassembly. The Ice Guide is held in place by three tabs. The tricky part is "tilting" the center tab into it's hole/slot on the ice dispenser lever (center hole), then tilting it up to snap into place.... there is a very tight tolerance here, with the opening of the ice/water dispensing unit. Be sure to "lock out" the ice maker/water dispenser, in order to be able to use the light. Once snapped in place, all is well.

The cap will only fit on one way. Align with tabs on filter, twist on. Press the filter into place and press to seat. Locks into place.

Long shaft from motor to dispenser was stripped. I removed 2 screws from the shaft holder in door, lifted old shaft out, put new shaft in and replaced the 2 screws. Took 2 mins! Works great!

Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.