KHWS02RWH0 KitchenAid Washer - Instructions

I removed the back panel to access the top end of the hose then I removed the lower front panel to access the lower end of the hose that attaches to the pump. The hose is secured with spring clamps and they were removed with pliers, the panels are secured with screws.

I replaced the hose and reinstalled the panels and I was done.

It was fast and pretty easy to do.

Followed internet instructions

Removed the three screws in the back took off the top and swamped out the part. I recommend that the inlet valve is checked periodically by removing the hoses to see if there's any build up on the filter.

We removed the front cover to the washer. Then we removed the drain pump piece that was broken. We put the new drain pump in and secured the screws. We also inspected all the hoses to make sure the hose clamps were intact. Then leaving the front cover off the machine to inspect for leaks we turned on the wash cycle. No more problems.

place new baffle over slots in drum; move toward back of drum and snap in to place pressing down and moving toward front of drum

Unplugged power cord, turned off both water valves on the wall, Disconnected the water hoses o the back where they are attached to the water inlet valve. Note: there will likely be some water left in the hoses. Then removed top lid of washer (this is a front load washer) by removing the 3 nut screws on the back of the lid and sliding it to the back and lifting off.. Disconnected the small hose that is attached to the water inlet valve by squeezing the hose clamp and sliding the hose off. Removed the 4 wires connected to the water inlet valve (marked each one with a number in order) then removed the Phillips head screw on the back of the machine holding the water inlet valve, sliding the valve to the right, . Removed valve, and replaced with new one, and re-installed by reversing order of removal.

firts remover the three bolts that held the front panel on, and removed that. Then removed the screw that held the pump in place. then removed the hoses from the pump. After that put hoses on new pump and srewed back in place . the put front back on.

Removed the 3 screws that hold the bottom front panel in place. Removed the 3 screws that hold the door latch in place and pulled out on the bottom of the door which wasn't very much and slid the door latch out to get to the wire connections. Connected the wires to the new latch and pulled out bottom again and put the latch back into place and put the 3 screws back in. Note: make sure you unplug the washer so you don't have a chance to get shocked. Level of difficulty was pretty easy.

Easily. 4 Screws. 2 Clamps.

Remove three screws on bottom panel lift up and remove panel.The water pump in right in front. One screw holds it in place and the input and output hoses are on the back side.The hose clamps are a little hard to take off I found that before taking the one screw off the pump remove these two lines.Putting the pump back in secure the pump with the one screw. The output line is easy the intake line can be a bit of a more work to get it on because the rubber is so thin.Getting this hose and clamp was tough. Most of all use a wet vac to remove water in washer and vac out the line to drain doing this will be water free during replacing water pump.Run a cycle to make sure the lins do not leak. The other is the people that has posted this replacement are very good

Easiest repair on 2003 front loading washer. This unit cleverly uses star tool machine screws with a hex head so you can pick your favorite tool. Turn off the water supply. Remove the hot and cold hoses at the inlet valve, draining any water into a small bucket. Have a towel for dribbles. *This is a good time to examine the hoses and replace them if they are anything other than perfect. Burst or leaking hoses is the #1 cause of water damage in homes.* Three screws releases the top cover which slides 1/2 inch back and lifts off easily. Remove one screw securing the inlet valve (same size screw as the others). Pull the old inlet valve away from the rear panel for easier access. Remove the 4 wires from the solenoids (they pull straight off but maybe need a little finesse), and re-attach to the new inlet valve. Using pliers, release the hose clamp on the old valve sliding it down a couple of inches, then move the hose to the new valve and reposition the hose clamp. Toss the old inlet valve in the trash, screw the new one in place, replace the top panel, reattach and hand-tighten your hoses, turn on the water, look for any leaks, and go have a three martini lunch with the money and time you saved.

Inserted new baffle in washer and slide in place.

Simple repair. #20 Torx, pair of pliers and 10 minutes to complete the job. Part was exact fit. Turned off the water supply, removed the three screws at the back, slid the top to the back and lifted it off to reveal the valve. Removed the screw holding the valve in place, slid the valve to the right and pulled the valve out to the inside. Used pliers to move the hose retainer off the valve, removed the hose, unplugged the wires, and reversed the procedure to install the new valve.

Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together