KHMS1850SSS2 KitchenAid Microwave - Instructions

All I had to do was lay the new tray in the microwave. Easy as pie. Also, the new tray arrived very quickly.

I noticed on some of the installation instructions provided by others that numerous individuals have experienced the same problem. I decided to try to lengthen the life of my repair and so I added an aluminum screen patch and some expoxy glue to the tabs that hold the screws. I figured that this might provide some additional strength to the grille and hopefully I wouldn't have to repair it again. Time will tell if this modification will be successful.

Ordered the item on a Monday at 12pm and it arrived the next day. Amazing!

just replace need cooking tray

I called the repair/parts number to make sure I had correct parts and the young lady instructed me as to the size of the serving tray; within 48 hours we had the VERY carefully wrapped carton opened and back in the microwave, working perfectly. Thank you. We'll recommend you to our friends!

Replaced light bulb.

First let me say that I tried several places to get what I thought was a simple light bulb. This included several national hardware stores as well as a national electrical supply company. No luck. Went to the manual and PartSelect. Not only did you have it in stock, ship right away,at a reasonable price it arrived in a matter of days. One would not normally think of receiving a "how to" video to change a light bulb but you did. That impressed me. Suffice to say the replacement went well and you can be certain the next time I need a part I will go to you first. I am also impressed with the organizations with which you are affiliated with. BBB, Norton, PayPal, money back guarantee etc. Thank You The entire process was made pleasant with your support.

You had alerted that it was imperative to unplug unit before starting to remove defective bulb. As described, there was silicon on bulb and socket and bulb broke upon my attempt to remove. Had to use needle nose pliers to get metal base of old bulb from socket, then all went well.

The problem I have with changing the bulb is my microwave is an overhead one and therefore I cannot tip it on its side to easily replace the bulb. I have to drop the lid down and carefully install the new bulb from underneath.

Used the new parts, they were a perfect match, I completed the work in 5 mins or less. The pictures provided were very helpful, and parts were delivered very fast. Price was the lowest too!!

I just opened the box and set it in. Took all of two minutes.

Removed the glass cover and replaced the bulb. Very simple.

Took the replacement plate out of the box and put it in the microwave in seconds. I never realized how much of a difference having the correct microwave plate would make. It's great to have it back.

I didn't do the repair -- my husband did, said it was easy, had no problems what so ever! The new bulbs give a lot more light to the cooking area.

This is an over stove top mounted oven. Remove oven from mount and place on a work surface with padding to support the lamps and vent holes. Strip the case off and locate the noted other "most likely" parts. Watch out for the Capasitor. Read the test note available for each part; Diode, Thermister Fix, Capasitor and Magnitron. Do the test checks. My issue wasn't obvious because I think the Capasitor was discharged and needed to be hot to check the Magnitron. (I'm not an electrical engineer so...) At this point I did the foolish thing...I plugged the unit in and ran it. Watching from a distance I saw sparks fly from the top side of the Magnitron with the same result from my cup of water (cold-no sprks here.) I replaced the diode and tried again, same result. I ordered the Mag and the Thrmst-Fix. Thrmst-Fix was on BO when the Mag got here so I installed the part. Had to remove several pieces to afford room to work and still had to stretch and pry to get the old out and new in. Mag is held in place with Torx screws so check that before you start. No other tool works. Mag was the problem for this unit. Some problems encountered: Parts and pieces were quick in arriving as long as they were not Back Ordered. Be careful to follow a thread for your product to order parts. These review/instructions are mixed for simular appliances and sometimes lead off to other part lists and numbers. Prices differ from model to model, list to list and the part numbers change. Go back to your product and then trace for the correct parts. I noted a $40 price dif.between Magnitrons from simular part lists. When you receive the part check to match the part numbers, Manuf. no. are different from the Part Select No. but can be crossed. Otherwise using this site's instructions, checks, insulated tools, big rubber gloves and a face shield I managed to save a $600 machine from the junk pile. Parts as ordered were recieved and return of un-touched parts were accepted by Parts Select without unexpected hassle. Thanks for a positive experience.