KEES705SWB0 KitchenAid Microwave Oven Combo - Instructions

First, my son pulled the range out and I unplugged it. Then he removed the 2 screws that hold the element in place. He then pulled the element out about 3 inches and disconnected the wires. Then he placed the new element in the oven, connected the wires and put in the screws back in. It worked immediately!!

I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.

Ordered the part Friday afternoon. It was delivered early on Saturday afternoon. Very impressed with the speed of the delivery! Power off, unscrew the old part, replace, screw the plate back on. Easy!

Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)

I read other other posts and followed their advice. Remove the 2 screws holding the element to the back of the oven...gently pull it out about 3" to reveal the connecting wires. I found the needle nose pliers were necessary to detach and reattach the wires. Don't yank! Be aware that the wires have a tendency to want to pull back into the back of the oven while they're loose. This was a wall oven and that woul've been a large problem if they they had. Otherwise it was a snap!

Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!

First, turn the breaker off to the oven, you don't want to electrocute yourself. There are two screws that hold the element to the back wall of the oven, undo those and pull the element towards you. There are two terminals at each end of the element, take these off, then reattach to the new element and screw back in to the back wall of the oven. This process takes maybe all of five minutes

removed the two screws that hold the element in place, then slowly pulled the element out and disconnected the two wires, then reconnected the wires and screwed it back in - I'm a 25 year old female and did this in less than 5 min. - don't wait any longer to fix your oven!

First I unpluged the stove, then I removed the two screws that hold the heat element in place. Then I pulled the heat element out a couple of inches and disconnected the two wires.
I just plugged in the new element wires, pushed the element in place and replaced the screws.
It only took about 10 minutes at the most.

Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Then reverse the process and bingo ...done

EXTREMELY fast shipping of product ...I have purchased other products and always satisfied .

I read other repair stories before I completed the instillation and let me tell you that in it's self was a great help.

Very easy to install two screws in the front but you must first remove the wires behind the oven otherwise you may damage the wires by pulling them through.

Part was on order and I still received it within three days.

You guys are the best, I recommend the site to all of my friends and family.

my wife took the old element out i used a screw driver to remove it...i then ordered the new part using this web site...i then let my wife install the new element she then attatched the wires she used her fingers to tighten the bolt....and she is very very impressed with herself.

ordered new broiler pan