KBWS22KCBL00 KitchenAid Refrigerator - Instructions

Just slipped it in. I think it's a very poor design.

in stalled new circuit board an thermostat an was fixed

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

The video on the part select website with the Canadian gentleman was absolutely the best! My wife and I watched it and was able to accomplish the replacement with no surprises or issues. One tip that we could add is that the orientation of the temperature sensor was not specified in the video, but the slot seemed to work better for one orientation versus another. It has been a couple weeks since the repair and the refrigerator is working like it did when we first purchased it.

Removed the freezer door, by loosening 4 screws and pulling upwards to disengage door from frame. Removed the top basket by pulling up on both slides on the gear shaft sides, note they have retaining tabs you must push in. once the slide / guards are up the top basket comes out. Remove the bottom basket. Remove to angled screws on the top tracks and remove. Remove 6 screws on bottom slides, 3 per side and slide out as a whole unit. Unplug the ice maker, remove 3 screws for it to come out. Note I cleaned mine while it was out with vinegar to remove the mineral build up on it. Remove the screws in the back panel, and pull it forwards. The top vent has 2 clips that hold it in and you will need to remove it prior to fully removing the plate. The plug for the icemaker needs to be removed also. Pull the back plate out. Once the plate is out you can see the fan and access it. Unplug the clips that hold the wiring harness secure. 2 screws to remove the fan assembly. Once fan assembly is out, disassemble it, then reverse assemble it with new parts and fire it up. Mine took right off and running like its brand new.

I'm a 37 year old woman who has never worked on a fridge before, ever.
I was able to google how to run diagnostics on it and determine what the issue was.
Once I received the part I was able to take apart the freezer to get to the motor. Remove the old motor and install the new motor.
This was extremely easy I watched a couple of the youtube videos provided here and now it's running just fine.

The part just snapped in. super easy.

Pulled out broken parts and snapped/ pushed into place new ladder hooks 15 min max

Took the new kick plate out of the box. Snapped it into position. I have had a repairman for this refrigerator before. I would rather repair an appliance than buy a new one. I'm very proud that I thought to get a replacement part myself instead of calling my friendly repairman again. Saved a few dollars.

The icing n the freezer and wetness/ humidity in the fridge would not stop. I reasoned the freezer seal was bad and letting the outside humidity in. This fridge had been moved to the garage after a new one was put in my house. The new door seals completely fixed the problem, works perfectly now.

Complete replacement of the plastic drawer.

Opened the bottom freezer door and pulled the gasket out of the groove. Pulled it out around the door and put the new one back around the door and the pressed into the groove. There was one place that a flat spot didn't take shape so I used a blow dryer to heat it up some and now it seals perfectly.

Unscrewed bulb from sock .
Replaced with new one . Now working

Very simple fix, remove 3 screws, two connectors to the old switch

It took longer to empty the glass shelf above the Crisper Bins than to replace the rail. Since the part simply snaps in place, no tools were required