K45SSWH3 KitchenAid Mixer - Instructions

Used youtube movies to disassemble the mixer and found that the gear was stripped. I kept the screws in labeled ziploc baggies so I wouldn't forget which screws went where. Once the part arrived, it was very simple to replace the gear. I regreased the mixer and then reassembled. The trickiest part was how greasy everything was! It was also hard to get the pin through the beater hub - I found a video that suggested using a very slim screwdriver to thread the hole before inserting the pin. This was the most involved part replacement I've done on my own, and it was very satisfying to get my mixer back in working order!

Unscrewed the existing screw cap, put the new one in place, replaced the screws. So easy!

INSTALLED PHASE CONTROL BOARD AND SPEED CONTROL PLATE, BOTH AT SAME TIME
Your DYI video was helpful, especially holding the spring with a cloth. Also good for fine tuning to get the speed exact

Followed web site's videos. One step left out of video.

I did exactly what the PartSelect video demonstrated after watching other DIY videos on the Internet, thus I did not remove the stand which seemed like a little too much for a simple straight forward repair. This is the second time I have replaced this gear. The first time was about 10 years ago when the bakelite gear broke on a 30 year old KitchenAid K
-45. That mixer made hundreds of loaves of bread after grinding many pounds of wheat berries. The only reason we had to replace it was that it walked off the flour dusted counter and landed on its head when my wife had her back turned. Otherwise we would still be using it. :-)
Thanks for the excellent service and instructions.

replaced gear, and brushes.

I watched a YouTube video all the way through, then watched each segment and followed along with the video. It was messier than the professional repair guy, but it worked out fine. This is not a difficult repair when you can watch a video and follow along. It saved me about $130.

You tube has great instructions! I would suggest when you buy a part to let customer know that they need a food grade gear grease ordered to complete the reinstall of all gears and body parts!

Dismantled the mixer, took photos, and re-assembled unit.

To access the interior of the mixer, I first removed the single screw holding the cup-shaped part at the rear. Then I removed the 4 large screws on the under surface of the mixer head. Next I removed the bright metal ring around the planetary gear area by prying it off. I then pried the dish-shaped part off the shaft using a large-bladed screwdriver. This exposed 5 screws on the circumference of the planetary gear. By removing them, one can pull up the gears and see into the area below. I found the worm gear had fractured. By removing 3 screws at the base I extracted it for closer inspection, checking for any loose pieces. Beware of the jelly-like grease. The replacement part goes into position, and one then follows the steps in reverse.

Really no help from Kitchen Aid sources; but phone call to PartSelect solved the problem. Kitchen Aid repair line didn't even know the part #! Thanks to Part/Select, Christmas cookies are being made.

followed the emailed instructions from your company
worked perfectly
thanks

Tried new brushes but alas it looks like it was a controller. Wife needed it asap so Ii bought her a new one. Service and delivery were quick but couldn't wait for a second part to try and repair it again.

I decided to update the motor brushes in our KitchenA id mixer even though it operated perfectly for years. After installing the motor brushes, you sent,I plugged the cord attached to the mixer into the outlet. I selected 1 on the speed selector and nothing occurred. The mixer would not operate. I then checked the outlet to insure there was voltage present; there was voltage present. I again plugged the cord of the mixer into the outlet, selected 1, then 5, and finally 10, with no results. The mixer would not operate. Finally, I removed the motor brushes I had received from you and installed the old brushes that were originally in the mixer, plugged it in the outlet, selected 1 and the mixer operated perfectly as it did BEFORE installing the brushes you sent.

When I took the back cover off I found two parts that "could" be the problem. The speed control plate was cracked which explained the spotty working. I ordered both parts and installed them very easily. The parts fit perfectly and resulted in the mixer working perfectly. I can't say enough about the excellent parts. They were perfect.